Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
I need to measure all width of continuous pulses without stopping the measurement. The pulse frequency is about 10kHz. But the frequency and the duty ratio changes dynamically...
Hello everyone,
It seems like a very basic issue but somehow I am unable to resolve it.
I have a characteristic of length 20 bytes. This characteristic is supposed to...
Hi everyone,
I am having problems in getting the twi peripheral to work properly with the accelerometer I am using ( NXP MM8653FC).
I am getting some wierd issues, firstly...
Hi,
I have noticed strange behavior when Android-Image-Transfer-Demo firmware is used (SDK13, softdevice 5.0.0-2.): Demo kit does not startup if powered from the coin battery...
Hello!
I am putting (with a wave generator) a square wave on pin 17 of the microcontroller, and I want that same wave to come out on pin 18.
How do I do that?
Do you have...
I'm using SDK v 12.2 project ble_central/ble_app_uart_c using GCC
After running the project for awhile a stack overflow in the ble_stack_thread() is detected which eventually...
Hi,
I'm modifying the light_switch client example, so that I can use GPIO as input instead of the button. I was able to build the modified example in SES and download it...
I'm attempting Mesh DFU on an Ubuntu 16.04 system. Here are the steps in the quick start guide along with corresponding notes on my setup:
nrfutil keys --gen-key private_key...
We are currently developing on the PCA10056 as we wait for our development boards. We would like to implement UART0 as a debug port, that we can output the log messages to...
Hi,
Can somebody explain how the Ax, Bx and Tx registers are used in the calculation of the temperature reported by the temperature sensor block in an nRF52832?
What we...
Hi,
I need to connect multiple SPI slaves in a daisy chain. It seems that using nrfx_spim_init once and nrfx_spim_xfer at each transfer is the simplest way to go using the...
hello, i want to synchronyze differents peripheral with a central thanks to the state of gpio i have this code but when i call gpiote() i hava nothing in return why ?
void...
I have done some reading on the forums and have seen that Martin Bohrs-Lind has ported the EMDv6.12 to SDKv14.2 and the nRF52832, here . I have keil v 5 compiling his work...
Hi
What would be the best way to interface a wireless charging circuit with a nRF52 device?
I've found a IC from Texas instruments that does the job, but is it safe to...
