Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
I noticed a possible issue in BSP_MS_TO_TICK macro computation.
In bsp.c, the macro is defined as:
#define BSP_MS_TO_TICK(MS) (m_app_ticks_per_100ms * (MS / 100...
Hi nordic,
Is there any ways to implement that my device connect with one special Central Device likes Andriod phone and Iphone. Currently I know is whitelist. First I add...
Hi;
Is it necessary to reset SoftDevice when using NVIC_SystemReset ()?
The SoftDevice must only be initialized if a chip reset has occured.
I saw the above comments...
Here is the code I'm using to test it out:
static float number = 0.5678905;
NRF_LOG_INFO("Float number: "NRF_LOG_FLOAT_MARKER"\n\r", NRF_LOG_FLOAT(number));
And...
Hello,
I am working on NRF52382 custom board, where I am running a timer of 30 sec to get a value every 30 sec.
I want to save this value in flash.I am well aware of...
Does the s210 softdevice not function on the nRF51822? I see it available for the nRF51422 here but it is listed under the 51422 only.
I have a v1.1.0 PCA10031 (nrf51422...
Hello,
I developed an application for the nrf51822 Smart Beacon, SDK11 s130, that basically advertises the battery lvl of the beacon, the staus of button_1 and the number...
I have a nRF 52 DK board. I have flashed dtm example onto it. I have connected a USB to serial UART interfacing board ( www.sparkfun.com/.../12731) to the respective Tx, Rx...
Both the capacitive touch library and the driver (which is better ?) are using the analog inputs.
There are only 8 of them , and we need 10 at least buttons.
Is there...
I'm migrating from SDK11 to SDK13. My custom service is based off Heart Rate Service, so I started from the new SDK13 example of HRS, and updated all the initialization code...
Hi,
on Android, I sometimes get delayed notifications. I measure realtime data and send them over notification, and I can see data change on Android with approx 1 s delay...
Could Nordic please confirm that the "SB13-SB15" and "SB23-SB25" silkscreen markings incorrectly imply that pin 1 of the SPI flash part, which is actually "!CS" would appear...
I have a custom PCB with an nrf51422 powered by a coin cell battery. The EE who designed the board assured me that the battery voltage could be measured internally through...
