Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, in our project we use the nRF52832 and a external flash memory MX25L3206E connected on this pins:
Take note in this project we also use SPIM0 to manage an IMU and...
Hi, I just purchased new PPK2 kit from mouser.
But after trying to open it via nrf Dekstop app it gives and error
2024-11-19T11:57:53.845Z INFO Selecting device with the...
Hello, I am trying to achieve a few uA current in nrf9160 but with even all conf off and empty while loop or even without the while loop the controller is consuming 5mA which...
We are currently working on a project based on nrf52840 and using connect sdk v17.0.0.
It is currently in development phase but eventually we are planning to use nrf5340...
Using v2.8.0-rc2 as v2.7.0 doesn't support the SCRATCH partition.
I am not able to enable BOOT_ECDSA_TINYCRYPT (required for Image Encryption).
I suspect this is because...
Hello
Awhile back I profiled my battery using power up app @ 4C 25C and 45C for a battery between 2.75V and 4.2V battery model is attached in zip.
The profiles themselves...
Dear Nordic Team,
I am working on a project using the nRF7002DK and require guidance on implementing the following functionality:
Acquire data from a sensor using the...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
I am an embedded software engineer and have experience developing BLE devices with nRF5SDK, but this is my first time using Zephyr/NCS.
I am developing a USB dongle (nRF52840...
Hi,
I am developing a product based on the nRF9160 using the LwM2M client. I successfully have this working using PSK, but want to use X509.
I am calling lwm2m_security_set_certificate...
I'm migrating our project with custom boards from NCS 2.6.1 to 2.7.0, and I'm having a number of issues in the vscode extension (v2024.9.87):
The "Create a new board"...
Hi,
We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB.
Do you have any reference designs for a PCB antenna which must be as small as possible...
Hi,
I'm getting an error when building the example temperature that says: Linking 'temperature_pca10040.elf' cannot open output file C:/Users/임선영/Documents/SEGGER Embedded...
Hello,
I am designing a LTE-M GNSS Tracker, that should also be able to scan for WIFI APs. I dont need to use LTE and WIFI at the same time, but rather like that:
Connect...
