I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I am trying to debug/flash an nRF54L15 using the nRF Connect VS code extension and a J-Link EDU. Although my J-Link EDU works fine with all the Segger tools, including Ozone...
Hi
I am looking to a wearable / health tracker which will be mounted on a persons head.
Are there any precertfied nRF7002 module where I don't need to go through the pain...
We tested several hundred connection and disconnection cycles with the nRF52840 BLE dongle. The first hundred cycles operated without any issues. However, at a later cycle...
Hello, I am trying to use twister + ztest to run some basic tests on my device custom project and nrf5340 Here are the contents. Current Directory Structure
Contents of...
Hello there,
I'm developing a project with NTN using a Vivo chip, a Brazil operator chip, but I'm having trouble with an nRF9151 and I'm trying to put it in NTN mode, but...
Hi
I took over a nordic project and was asked about the bluetooth version used in that project.
How Do I figure this out?
I am using a nrf52833. The firmware is developed...
Hi all
While connecting to a peripheral that has ble buttonless dfu characteristic i need to enable indicate.
Undortunately i get back err: 0x11(17) from sd_ble_gat...
I'm struggling with the nrf sdk v2.9.2 zigbee light_switch example. I copy the example, add this to proj.conf
CONFIG_ZIGBEE_CHANNEL=25 CONFIG_ZIGBEE_CHANNEL_SELECTION_MODE_SINGLE...
Hi.
I have a question.
When sending packets from a ZIGBEE product (with TI CC2538 built in) and receiving them with an nRF52840 Dongle (Sniffer FW) and Wireshark, is it...
Hello Everyone, I was wondering if there is any easy "ready configuration" way to directly set BLE advertising and connection interval with adding some config to the prj.conf...
Hello! Using NCS 3.2.1 I am implementing DFU over SPI (the NRF54L15 is SPI slave) using the "DFU Target" library. It works very well, as long as I am connected with JLink...
Hello,
I want to read a status register in my SPI peripheral. Once I send my read request, the peripheral will send the status byte over and over, and I want to watch for...
I have been testing this for some time and I cannot figure out why lorawan_send() on zephyr does not work when called from a thread, while calling it from main() works perfectly...
Hello Nordic team,
I'm working with the nRF54L15 DK and using the latest NCS version that supports Bluetooth Channel Sounding. Here the sample is channel_sounding_ras_initiator...
Hello,
I am trying to run nRF sample of cellular LWM2M client on nRF9151 development kit that communicates with a custom Leshan server over the LTE-M. Security modes of...
