Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I'm developing custom firmware with Keil 5.31 and SDK 17.0.0. I have to configure the SDK and so I started to edit sdk_config.h, but it's quite hard to read the whole...
Hi, all
I am learning SIG mesh
I wanna know:
1. the current of the LPN node, could you provide me some relevant data ?
2. does the provisioner need to keep some...
Hi,
I am studying openthread, I don't understand what is Dataset in Openthread used for? It is just for backup some network parameters? How could I use the Dataset?
...
I am trying to read the analog signal to convert it to digital signal on the nrf52820, however, the saadc example is not working on this chip. Do anyone has an idea how to...
Hi Devzone:
From this page describing 2.4Ghz Radio in infocenter:
2 Mbps nRF mode ideal transmitter has a sensibility of -89 dBm
2 Mbps BLE ideal transmitter, packet...
Hello, I see as of nRF5_SDK_15.0.0_a53641a the ble_hids service now supports multiple links. Do you plan on supporting multilink ANCS in the next release of the SDK? Thanks...
Hello Sir
I will use NRF51822 in my project.
But i have read it can be connect eight channles in the same time.
But i need in my project control of 32 devices (channels...
I am making a ble project on nrf52840. I am having trouble finding the idea of adding a new node to the network. My project follows a set of main gateways and additional nodes...
Sir i have NRF52840 dongle i used many times works amazing.After i uploaded Gpio toggle program now dongle is like dead ,laptop is not detecting it, i can't see it in device...
We are adding social distance feature to our existing product. We are facing performance issue. The device has one peripheral role and one observer role. I have set scanning...
HI :
softdevice version : s132_nrf52_7.0.1_softdevice
SDK version ： nRF5SDK160098a08e2.zip
example ： ble_app_hids_mouse
IOS : When IOS system bluetooth has bonded...
We're seeing an issue where the soft device stops responding and ultimately disconnects with the reason BLE_HCI_INSTANT_PASSED. The disconnection only seems to happen when...
Hi ,
I have Android App acts as a peripheral app . and nRF9160dk as central mode.
I'm trying to scan for the android app , but not sure which filter to use. I referred...
Hi!
I'm trying to run Asset-Tracker routine with 9160dk to connect to the NRF cloud(ncs1.3.0). The China Telecom can't connect the nrf cloud, China Mobile can connect normally...
Hi All,
To enable infinite advertisement in ble_app_buttonless_dfu example, I di following change
#define APP_ADV_DURATION 0 //18000
But after this change, the device...
