Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Based on Android studio 3.0, gradle-4.10.1 compile the project downloaded from github.com/.../android-nrf-mesh-library . I get the following error:
The module 'app' is an...
Hi,
I have an external flash ( via QSPI ) working on NRF52840 Based product.
I'd like to redirect all NRF_LOG message to a file , is there a similar log backend available...
Dear developers,
My device uses the NRF52840 SoC and is equipped with a modem for internet access.
To perform firmware upgrade, I imagine I would have to download a DFU...
Hello, I tried to work with nRF52832 to read adxl362 registers, Here is my function to read all 3 received bytes from adxl362 (according to datasheets, the last byte must...
Hi,
I tried to install the latest sniffer v3.0.0 and Wireshark v3.2.0 on my computer. I could not see PCA10056 listed. If I start my wireshark from command line, with "open...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). My goal is to send data from sensor over bluetooth...
When i used Port 0 assigned on Uarte rx tx pin , everything was ok.
But when i changed the rx tx pin to port 1 , for example p1.00,p1.08.p1.09, it doznt work...
i am sure...
I use nrf5_SDK_for_Mesh_v3.2.0_src , nRF5_SDK_15.3.0_59ac345 and board pca10040.
Copy the ble_app_uart_coexist folder into the examples/ble_peripheral folder at your nRF5...
Hello.
I'm doing a DFU customization now.
However, because of the problem of data transmission of the last packet of the first page when advertising,
connection and...
I am setting up a relatively complex project that runs on top of FreeRTOS and it is based on the HRS freertos sample app from SDK 16.0.0. The device will need to run in several...
Hello,
I am trying to setup a PAN coordinator by following these steps:
1. mlme_reset_req() -> successfully responds with a mlme_reset_conf_t by calling the callback...
Hi,
I am using 52840 (WLCSP package) in a design. I am a hardware guy and no SW guy has been assigned to this yet. Can you please check my SPI pin assignment below and let...
