Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
I am using nrf connect app on ios , the device is getitng on device mode but it is not showing DFU button on it , but it is working when using android app of it
And...
I want to generate a custom delay of one microsecond without using any timers By simply Executing instructions I want to generate. is there any possibility please let me know...
I have a rather strange issue.
I developed an application on the nrf52832 which amongst other, communicates with an ST Micro accelerometer LIS2DE12. The application works...
Hello,
Library seems to have limitation to 1kB. I'am talking about deffered mode.
You can increase NRF_LOG_DEFERRED_BUFSIZE >1kB, but it will crash if you try to print...
Hello, I am new to developing with nrf and have been trying to follow tutorials on individually setting pins as output. I am working on just getting a specified pin to blink...
Hi everyone,
Recently, I downloaded the SEGGER Embedded Studio, release 4.18, and start the development of a Heart Rate Monitor using nRF51422 and SDK 10 (softdevice s310...
I am only able to successfully trigger the ACK payload interrupt on the nRF24L01+ if I mismatch the payload lengths on the two devices; 4 for the nRF24L01+ and 1 for the nRF52840...
Hi everybody,
Intro facts :
I'm migrating from SDK 13.2.0 through SDK 14.2 to SDK 15.3.0. My program build on SDK14.2 but my product didn't work as expected, then I...
I need the P9 connector pinout (or complete schematic of Thingy:52 ) for programming my Nordic Thingy:52 using SWD. I have found this topics:
https://devzone.nordicsemi...
Hello, according to your website, nRF24 Series family is not recommended for new designs... as substitution you recommend to use nRF52 Series family. Can I ask you for the...
Aim: interface nrf32852 with i.MX6UL based Linux board through UART and configure hci of bluez. Board: nrf52_pca10040 SOM : nRf32852 OS: Zephyr UART: we followed HCI_UART...
Dear Nordic Team,
We are developing a custom board with nRF9160 with application of tracting device.
I am new user to this module and designing our device with target...
Hello,
I'm searching every where but i can't find what i want. Actually, i'm using two device and i really need to synchronise the execution of a process on both of them...
Hi All,
I have a problem to enable notification on my Android phone, i followed the tutorial on android web page (section bluetooth low energy) but my app crash, i have...
I understood how external board programming works with nrf52840 DK.
Debug IN (P18) is used for external debugger while Debug OUT (P19) supports external board programming...
