I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I want to create a program for communication and control between the NRF module and the desktop. I followed the instructions Installing from https://github.com/NordicSemiconductor...
Hi!
I'm working on a toy based on the nRF52810.
The BLE requirements are very low:
- Peripheral only
- 1 link only
- No bonding/pairing, no encryption, no whitelist...
i can create three service each with one notifiable characteristic. i am using nrf connect to test if it is work and i am able to send data through UART Rx and then enabled...
HI,
I'm use nrf51822 and SDK 10. I want to use APP_ERROR_CHECK function to show error msg, I did also enable LOG function to support this, but it do not work.
here is...
HI everyone!
My case:
nRF52832 + toolbox on iOS and Android
I have device pre-programmed using seeger with settings:
Next I want to make DFU update using .zip...
I am trying to receive data from GPS L80 with the nrf52832 board but I am not able to receive anything. I connected the Rx of nrf52832 with GPS and vice versa. I also connected...
Hello, I'm trying to get manufacturer specific data from peripheral, but I don't know how to do this when the peripheral is using extended advertisement with LE Coded PHY...
Currently, I am trying to create a UART connection between the nRF52840 Dongle and my PC. I am working with the usbd_ble_uart example found in the dongle SDK. I managed to...
Hi,
I am using nRF52840 Preview DK with SDK v15.3.0 and Softdevice version 6.1.1
I modified the Blinky peripheral code to advertise over Coded Phy, this code is working...
Hi all,
We are working on a project that requires us to measure the resistance of something applied externally. We are mainly interested in the change of resistance over...
Hi, I have managed to send data to a dedicated server, but I have a problem with reconnection. After re-connection, this is what I get as an output. In the log, there are...
Hi, I'm using Nrf52840 as the MCU for the developed product.
For my product, there is a central and a peripheral which two are communicate with each other via bluetooth...
Does anyone have any guidelines on connection parameter guidelines for Windows 10 BLE 4.1 machines? When I attempt to set some connection parameters on the nordic 'slave/perpherial...
Hi,
I need to use 6 saadc channels to sample voltage on my project. The saadc channel 0 could be configured to connect different inputs(ANI0~AIN7).But I try to configue...
