Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
We are using this device and we seem to have an issue reading from P0.20.
I know this is a dual purpose pin. We have programmed it for input with pullup. We have it attached...
I am currently porting my project from SDK13.0 to 14.0 so I can use s332 v5.0.0.
I receive warnings when compiling
.\_build\nrf52_firmware.axf: Warning: L6330W: Undefined...
I would like to know if it's possible to pair two NRF52832 together using NFC. NOT an android phone to an NRF52, but a central NRF52 standalone connect to a peripheral NRF52...
Hello,
I am using nrf52832 with SDK12 with gcc compiler. I have extended the ble_app_template example with 2 services.
I have 1 timer interrupt using RTC(100 ms) and...
I've been noticing lately when running debugging on my code, a few minutes in it loses connection and says No Source Available for "0x01e054". I'm sure how to even figure...
I am trying to debug a custom version of the bootloader_secure_ble example but am running into FLASH space issues. The bootloader app does not fit into FLASH with -Og optimization...
Hello,
I am using Keil IDE for a while,and it is working perfect so far until, my code size gets bigger than 32K, I also decided to try GCC. I noticed GCC code size for identical...
nRF52832
SDK14.0
Hi,
I had two questions regarding Fstorage:
The Fstorage module works by having a queue of NVM operations. This queue only holds two types...
Hello!
I am using the nRF52832 with nRF5_SDK 14.0.0. with a JLink connection. My OS is Ubuntu 16.04.
After placing NRF_LOG_INFO() statements around my code, connecting...
Hi,
I am working on an application that needs to use pairing/bonding. I am incorporating peer manager into the project. I have included in Makefile paths the following...
I'm a little confused here...I have a basic main function which is turning on/off some GPIO and logging through SEGGER_RTT.
I thought that in order for that to work, you...
Hi,
I'm trying to get SPI working with an accelerometer (LIS3DH). I'm currently trying to use the nrf_drv_spi_transfer() function. See code snippets below.
// Initialize...
SDK14.0.0
nRF52832
s132
I would like to DFU the contents of the App Data section. In particular, I would like to erase the contents for a "factory reset" command.
...
I am setting up the DFU example to compile in Clion using ARMGCC 4.9 2015q3 and cmake. Everything compiled as it should and the DFU advertises. However, when trying to do...
hello there,
i want to send and receive data using spi and i2c protocol and i am using nrf51422 .how to interface which pins should i use to make spi and i2c communication...
