Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I'm using nrf_drv_twi to talk to an accelerometer from an nRF51822 on a custom board. I'm on SDK 10.0.0. I'm following the example from the SDK, peripheral/twi_sensor. And...
Hi,
I set advertising data as follows:
err_code = ble_advdata_set(&advdata, NULL);
But I can't achieve advertising without ScanResponse，could you give me some suggestions...
Hello,
I do connections between 2 nrf51 with a known and static services. Is that possible to bypass the discovery to access a characteristics (i know all characteristics...
Hi,
I am having problems using the the dfu_dual_bank_ble_s110_pca10028 example on a nrf51822_xxAA device.
I have changed the memory ares to:
IROM 1: 0x3C000, 0x3C00...
So long story short - I need to pair two devices: Arduino UNO with Seeed BLE Shield and Adafruit Feather 32u4 Bluefruit LE.
Now, Seeed shield is configured, and is able...
Hello, I am now having problems to get NRF51 DK to work. My computer is connected to board with USB. It can recognize it.
Now, here is what is something strange, when...
Not sure if this is the correct place to ask this question.
I can't seem to find the download location for the Master Control Panel PC application. It seems to only available...
Hello,
I am currently trying to generate a PWM signal on P0.00 and am not having success. If I drive P0.00 without PWM, everything works fine. Is there anything that would...
I have 2 nRF51 Development kits and a nRF51 dongle that I am using for proof of concepts. I am mainly using the nRF51 IoT SDK because we are looking at using IPv6 with 6LoWPAN...
I'm looking at log_uart_init in the nRF5_SDK_11.0.0-2.alpha and wondering if it would make more sense to allow the application writer to pass in a baud rate.
I'm trying to program a nrf51822 custom board using the SWD interface of the nrf51 DK. The board is using the low voltage configuration.
I'm not duplicating this question...
The IoT SDK Documentation page is getting Error 404 not Found.
Here is the error:
The requested URL /nRF51_IoT_SDK/doc/iot/html/index.html was not found on this server...
I know the softdevice region in the nrf51 is determined by the CLENR0 register.
But I read that the CLENR0 register is removed from the nrf52 and the MWU can be used to achieve...
