Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello,
I've built "bootloader" project in sdk6 and sdk8, which named "sdk6_bootloader.hex" and "sdk8_bootloader". Then what I did are listed as below:
(1)
using ...
I am trying DFU with:
BOARD_PCA10040,
nRF52_SDK_0.9.2_dbc28c9
s132_nrf52_1.0.0-3.alpha
One interesting thing is the SDK_0.9.2_dbc28c9 can not work with
...
Hi,
We currently (no pun intended!) don't have any battery protection circuitry for reverse polarity designed into our prototypes. Our device is powered from a CR2450 coin...
Dear Nordic.
I read specific data using GPIO(timer sampling), BUT, occasionally, the data is broken because of Softdevice interrupt.
So I want to guarantee it while reading...
Code_Replace_MainDotC.docx
Please look at the attachment of my code. Go to \nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s130\arm5_no_packs...
Hello everyone.
I would like to ask if is possible to compile and run examples from latest IoT SDK 0.9.0 on pca10028 board. Every example has only Makefile for latest pca10041...
Dear Developer Zone,
I'm using an nrf51822 with SDK8 & SD S110 v8
We have an iOS app connecting to a custom service on the NRF device. What we would like to do control...
hi,
i have a project which need dfu by OTA,but nrf51822 flash is not enough.The project detail information in the following:
chip:nrf51822QFACA10
SDK6.0
SOFTDEVICE:7.3...
I'm using nrf_drv_twi to talk to an accelerometer from an nRF51822 on a custom board. I'm on SDK 10.0.0. I'm following the example from the SDK, peripheral/twi_sensor. And...
Hi,
I set advertising data as follows:
err_code = ble_advdata_set(&advdata, NULL);
But I can't achieve advertising without ScanResponse，could you give me some suggestions...
Hello,
I do connections between 2 nrf51 with a known and static services. Is that possible to bypass the discovery to access a characteristics (i know all characteristics...
Hi,
I am having problems using the the dfu_dual_bank_ble_s110_pca10028 example on a nrf51822_xxAA device.
I have changed the memory ares to:
IROM 1: 0x3C000, 0x3C00...
