Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
we are interested about the nRF51822 BTLE chip. We already wrote a BTLE stack (slave side only) for another chip (icytrx) and we would like to port it for this chip...
In my design, I have a SPI flash connected to the NRF51822. Additionally, the NRF51822 is connected to a separate microprocessor that needs to be able to access the SPI flash...
Hi,
I am trying to program the sample application given in sdk_nrf519_addon_v0.2.0-1.beta.zip file, and following the instructions in the readme.txt. However, when I try...
Hi, I'm just starting to learn my ways around the nRF5182 SDK, my goal is to implement a device with HID profile using this device. The device must work with Windows 7 (until...
I would like to profile some code execution time (moving between floating point and fixed point arithmetic). On the last Cortex-M3 I used, we had the DWT_CYCCNT register at...
Hi ,I am evaluating the nRF58122 for BLE devices.
The nRF51822 Can we use "Multi-drop debug" on SWD?
We will use together also ARM microcontrollers other, I want to know...
this is quote from AN36> 4.2 Set up
The nRF51822 Evaluation Kit is needed for this application example. However, it is possible to modify the
project to also work with...
Hi!
I know this might be a stupid question to you but still... I am not able to disable i.e. a timer0 cc(3) IRQ.
My way to enable it in first place:
NRF_TIMER0->INTENSET...
hi guys,
i am trying to write my own application using ble_app_template for nRF51822, but i am not at all understanding the code, did anyone developed the code for it?...
hi,
i add bond function on my project ,
now the Master Control Panel can work correctly(show the Confirm Box )
but the iOS app(on LightBlue),not show any Confirm Box for...
Is possible to put S110 in observer role (as peripheral) , waiting for a specific advertising (or waiting for an active scanning) and then switch to advertiser role (always...
Hello all,
I'd like to use NRF UART App sample code (newest iOS7 version) to send data from iOS6 to nrf51822 for "real time" data transmission. But I found that when I...
Hi,
I am having some issues transferring data from an iPhone to the nRF51822.
Actually, I write block of 16 of my data from the iPhone on a specific characteristic on...
Hello,
I have been reading the documentation about how to program a BLuetooth Low Energy application. In that document, a lot of references to an specific mannual (nRF51822S110...
I am writing one bootloader to decide two apps resided in 0x14000 to 0x40000 with nrf51822 to run. Two apps works fine when starting running itself. But when bootloader switch...
