I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
I'm writing a program that swaps between LTE and GPS to send the device's location to AWS over MQTT. I am able to connect to LTE and AWS, then swap to GPS and get a...
Hello. I 've got such problem with flashing some of the ESB protocol examples of NRF5 SDK. I use Adafruit Feather NRF52832 board with ST-LINK V2 debugger. https://www.adafruit...
I want to implement UART service which can act as central and peripheral at at time.
I am using nrf52832 board and sdk 15.
I tried to implement it by changing the services...
Hi,
I am following the nRF_Sniffer_UG_v2.2.pdf to setup the nrfSniffer. Wireshark does not show me my board among the interfaces. I had a look at the troubleshooting part...
Hi,
We are developing a Bluetooth 2d-3d mouse with OTA -DFU service.
The controller we are using NRF52832 QFABB0 it contain 32KB RAM and 256KB of flash memory.
SDK...
I try to add NUS service in example ble_app_hrs_rscs_relay.
I have fail on send data from "Relay" to smart phone iOS nRF Toolbox.
1. I have modify the MTU size . #define...
I am using a ultra-miniature (BMD-350) series module from Rigdo which has the nRF52832 BLE SoC. The pins from the nrf52 SoC are all brought out on a female headers on a custom...
Hello.
Currently, we are developing based on "multirole_lesc", a BLE multi-role project. The project contains the BLE service “hrm”, but I want to add the “RSCS” service...
Dear Nordic fellows,
I have a Rigado BMD-350 that can transmit correctly bytes to another device via UARTE, but who cannot receive data correctly.
I'm using SDK15.3...
Thank you Nordic team for your precious help. Is by any chance the project sdk_15_gzp_dynamic_pairing_ses_device.zip also available to download? Is there any particular reason...
Hi,
I already read all the forum posts about this buffer order swap problem of the SAADC. Especially this one: https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in...
I'm upgrading a big project from SDK 6.0 to SDK 12.3, everything's going well, but I had to comment out a library because in SDK 6.0 the previous developer uses the input...
Hello there
I am trying to program the BL651 wich makes use of nRF52810 chip, however i haven't been able to program it.
The tool im using for the task is the J-Link...
from SDK 3.1 for thread and zigbee in simple coap server
after any time it go to disabled mode and no response
what means the flags? why is it disabled and do not...
Hi,
I want to create my own bootloader for the nrf52810. If i don't want to update my softdevice i just put my bootloader code just after my softdevice.
But it is not...
