Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello! I'm trying to develop an Android-nRF-Toolbox App. What features and folders do i use with show logs? In order to develop the uart in the toolbox app, we have deleted...
Hi everyone,
I want to know that is it possible to send the heart rate data using HRM services without sending the battery data in nRF51422. When I disable the battery...
Hi! I've been working with the Thingy 91 and I've found that the SIM card was running out of data, so we decided to buy more data to keep working. The board was working as...
Hi,
I'm making a new design. I want to use the NRF52840. I also want a low power microphone interface.
PDM seems like a good idea, modern PDM mics have low power modes...
Hei
I've gotten the ipv6_coap_server example to run on the nRF51-dongle. I got the bt0 interface after connecting to the device and I am able to ping the device.
My...
Hi all,
Previously I spent some time to set up the nrfsniffer and with support I had succeeded; devzone.nordicsemi.com/.../setting-up-the-nrfsniffer
However as I have...
Hi
I want to modify the nrf9160 software samples from Nordic so I can use float with printk() and sscanf() functions.
I am also using gcc.
I try figure out how/where...
Hi,
As a part of FCC testing, I am trying use the following radio_tx_sweep_start(txpower,uiMode,channel_start,channel_end,delayms) with below parameters.
uint8_t txpower...
Hello, I have seen and heard of nrf52 alot that it can be used as payment card by using HCE technique. Can anyone please shed some light on it ? I want to know the way we...
Hi,
I'm running a nRF52832 connected through TRACE port to a Segger J-Trace Pro.
Some traces seem to be lost, and Segger support team tells me it is possible as nRF52832...
I have a few questions regarding AoA mode.
My goal is to append the CTE frame too a standard advertisement frame. I would like to use one of the following examples as the...
Hardware: nRF52840, running on dev kit PCA10056
Software: SDK 15.0.0, no soft device
I'm trying to get the POF comparator working, and after struggling in our product...
I just updated my project from SDK 15.3 to 16.0. I am using the nRF52840.
I am not receiving the APP_BUTTON_RELEASE event when waking up from a button press. It used to...
I am trying to the asset tracking application on nRF9160DK and following the steps mentioned in https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started...
