I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
Hi,
Do you have a better example than the one on nRF Cloud that can show me how to transform a HTTP GET /message from my thingy. Right now, the messages are nested and it...
While I know the 9160 does not support voice calls, I would like to know if the 9160 will accept mobile terminated (MT) data calls. If so, how is that represented in the firmware...
First of all , p lease forgive me for m y bad English if it annoys you .
I do have an interest in nRF52840 development kit, because I am trying to find a development kit...
After updating from THREAD SDK 2.0 to SDK 3.1 I am getting NRF_ERROR_NO_MEM in nrf_sdh.c.
The project is based from the multiprotocol BLE thread dynamic example.
The code...
I'm creating a ble central device that receives instructions via UART on which device to connect to and which UUID to write to.
I'm able to connect to a peripheral device...
Hi,
I am working with NRF52840 and want to encrypt my saved data with AES using CC310 cryptocell.
I am working with nrf_crypto_aes frontend to do AES.
I want to know...
Hello,
I'm trying to build and run 'secure_bootloader/pca10040_ble_debug/armgcc/' example and it seams that it stops with some hard fault:
Remote debugging using localhost...
Hi,
I tried to evaluate the light switch demo using the boards that I have to my disposal.
These are 1 nrf52-DK and 2 nrf52840 Dongles.
I wanted to use one dongle...
in application design , this pin is not connected to VDD , but application board works well ,
application's power range is 2.2V - 3.3V (AAA batteries), max current consumption...
I'm attempting to troubleshoot why my HM18 doesn't connect to the ESP32 over BLE. I'm now deep in the rabbit hole that is BLE sniffing so now I'm trying to determine if the...
Hello,
I did a side by side comparison of the latest nrfutil v6.0.0a0 vs v5.2. It looks like v6.0.0a0 is much slower.
Looking at the log from the target device, it looks...
Hi,
I have installed Embedded Studio for ARM v4.22. However, the studio crashes when I select 'Activate Your Free License'. Reinstalling does not help, and neither a different...
Hi,
In order to read values from TH02 sensor(Address: 0x40) I first need to give a command i.e. write 0x01(for temperature) and 0x11(for RH) resp into internal CONFIG register...
What is the least expensive J-Link Model is required to program a nRF52840 on a custom commercial PCB?
I see that it is a ARM Cortex-M4 core, but I want to double-check...
