Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi, we are looking at using a FCC pre-certified nRF52832 module such as the murata MBN52832. It would be for a wrist mounted product so will be in close proximity to the body...
Hi there Nordic Semi/ forum,
This is actually my first post here.
I got the NRF52 DK and I want to implement the NFC type 2 ( passive) tag with it that I could both read...
Hi, I am trying to use P0.9(nfc pin) as gpio(input) to read the charging status of a battery from battery charger IC(BQ 24230). the Open-Drain Charging Status Indication of...
hi Nordic engineer
hard platform : N53832DK, 51822DK
software platform nRF52832 use SDK_14.2.0, nRF51822 use SDK 12.3.0
nRF52832 as ecntral and peripheral; nRF51822...
Greetings,
in the system I develop I shall have a task resposible for fetching some amount of data from Flash to RAM. I should mention that the code will be executed from...
Hi,
I try to activate the bonding with the "ble_app_multiperipheral" exemple project I have modified.
It is very strange because I can bond as wanted but only if I set...
Hi all,
I am having query regarding BLE Security.
Which options are provided by BLE for security.
Can anyone provide option in below category?
1. Security in Connection...
Hi all,
Going through the sniffer document and devzone tickets, I observe that there is no official nRF sniffer software to emulate nRF52840 QIAACA SoC as BLE sniffer. ...
Hi Everyone
I was trying to use segger embedded studio for nrf52840 PDK.
I could get the example codes working but when i tried to create a new project and try to include...
Hello, I am trying to initialize the service Power Cycling from the files of this link https://devzone.nordicsemi.com/f/nordic-q-a/9169/cycling-power-service-0x1818
I get...
Hi,
I've been trying to use the nordic power profiler v1.1 with my nRF52 development board to figure out how much current is consumed during operation.
I used the power...
In the light-switch-proxy-client example there is every unreliable group message repeated a number of times (GROUP_MSG_REPEAT_COUNT). Is this always required to be implemented...
When the nRF53832 is connected with a cell phone for data transfer, can it still be discoverable, and go though pairing/bonding process with another cell phone? I think the...
Hi, Just porting an old project from nrf52832 to a nrf52810. I've had trouble finding a bare-bones project (arg-gcc), basically just main + log for the 52810.
I understand...
