Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
Greetings,
We have taken the RAM Retention example and are experiencing a failure (all LEDs on) when setting MAX_TEST_ITERATIONS to a value greater than 1. This is duplicated...
I am using nrf51822 with softdevice 7.3 and sdk6. I am having some strange problems in single bank bootloader. The nrftoolbox version 2.4.0 gets stuck at 94% during the firmware...
Hi,
(SDK v14.2, nRF52832)
I'm developing a Timeout Timer functionality, and was wandering if the following scenario is a good practice:
I don't want to have a interrupt...
Good morning everyone,
I am having a lot of problems configuring the Peer Manager.
I read several discussions on the topic, but either they are old (referring to ble_evt_dispatch...
Hello everyone,
I`ve 4 thingys and ran the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo . That works well.
Now I`m trying to add the nRF52 DK as a Node...
I am trying to perform a dfu upgrade according to: infocenter.nordicsemi.com/index.jsp
The exact command I am running is: nrfutil dfu ble -ic NRF52 -pkg dev_board_bl.zip...
There is something I want you to tell. Do you know how to allow other interrupts (specifically IRQ pin) while interrupting app_timer? I studied variously, but I can not find...
While I'm waiting on answers to other questions, I thought I would try to nrf_Logging with the Segger RTT up and running. It sounds like a pretty tool.
I have created a...
As picture, This is the external circuit of 52832, and I've drawn out P0.09,P0.10,P0.17,P0.18,P0.19,P0.22 of these six gpios, each of them for control purposes, and now P2...
Looking to make the nrf52 DK into a CR2032 coin cell battery tester. I tried a couple of sdk 15.0 examples, uart, proximity and another from a devzone case but not really...
I am using the nRF52840 development kit and running the SPI peripheral example in SDK 15.
I am having trouble displaying a static value in my watch window.
static const...
