Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
There is a bug in a Linux box (Mint x64) with the following configuration:
SEGGER Embedded Studio for ARM Release 3.34 Build 2017121400.34532 Linux x64.
Nordic...
Hi,
I am using ble_app_multilink_central and ble_app_uart central example for my application, i am combining these two example for ble_app_multilink_cenntral for BLE_NUS_C...
Hi,
I'm using the nrf_drv_twi driver (master) to communicate with a number of IO components, such as LEDs, buttons etc.
If my IO component does not respond (why is not...
I downloaded SDK 12.3.0 (seems to be it is the last supported SDK for PCA10028) and tried to use fats example, I changed pin configs to SPI's pins.
I also prepared my 16Gb...
Hi there,
I'm putting together a PoC board for a demo - in this case size matters and I've had to make some compromises for the sake of speed (which have increased footprint...
Hi,
After setting up constant carrier, how can one determine that it is working. With no modulation the receiver can't determine anything, can it?
thanks
Hi,
SPI use with SDK14.2.0 leads to very high power consumption (around 400 µA) on nRF52832 (QFAA). The same piece of code running with SDK12.3.0 has much lower power consumption...
We developed a device based on nrf51822.
We use SDK11 and module Device Manager to implement bonding.
We have received feedback from the user, that our deivice was bricked...
Hi,all :
I just want to know how to enable the nrf_log (in the ble example).The version of the sdk is 12.3.0 and the cpu is 51822 .Thank you very much .
On the nRF52810 is it posible to change the gain setting for the SAADC on demand? For example the SAADC is reaching its cap and then the gain is increased so it is posible...
I see the max for a BLE connectable advertising packet of 31 bytes. I am not sure if the manufacturer specific data which also can be up to 31 bytes is included in the overall...
Hi,
We have recently moved from using the nRF52840 PDK to a custom PCB. The custom PCB uses nRF52840 Q1AABB, while the PDK has Q1AAAA.
On the custom PCB, the code is getting...
Good evening,
I'm having some difficulties with the thingy52. I used it as the basis of development for the project and up to this point without major problems. However...
IARv8.x.x no longer seems to display the detailed peripheral register settings in debug mode under "View->Registers" as all v7.x.x versions used to do. In trying to determine...
Hi,
I followed this tutorial https://devzone.nordicsemi.com/tutorials/b/bluetooth-low-energy/posts/ble-characteristics-a-beginners-tutorial?CommentId=adb9d7e0-1bf3-49bf...
