It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
I read about Segger studio (on their website) that it reduces the code size. I try to check it out
Here's my opposite result
I've compiled the same app (e.g uart_example...
Hi all , when I run and debug my code , I frequently encounter error :
I think it's related RAM configuration on KeilC .
Please show me what is error ? And how to solve...
Hi there,
So I'm going through that complicated step of setting up the IDE for the first time to get started programming and I'm having issues doing it with the SES and...
hi everyone ,I want to ask you a question, I use the SDK12.3, when the device from the application transformation to the bootloader, when DFU is failed, why the deice is stays...
I am using nRF51822 (PTR5518A) with SDK v12 and s130 softdevice. To dump the code I am using nRF52 DK segger (PCA10036). With that I am able to dump the code but there is...
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
Hi,
I am able to connect nrf51822 with nordic app but now i want to receive data from nrf51822. For Example -
If nrf51822 detects some voltage at pin no "1" then it should...
Are there any Segger Embedded Studio examples for the nRF51 dev kit?
All the examples supplied with the nRF5_SDK_14.1.0 seem to be for the nRF52.
I only bought a new dev...
How do you do
E: \ Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_driver pwm_driver routines of the path,
1.How to configure reverse polarity...
In all the SDK examples all the source is in main.c. Is there a good reason for keeping everything including timer initialization, UART config, BLE setup, etc all in one file...
Hi,
I am using nrf51822 (pca10004) with SDK110 softdevice programmed through j-link LITE SEGGER. After programming the custom code (Basic I2C code) and when we try to debug...
Is there any documentation as to how to connect a nrf52 chip (as found on the nRF52832 BT Module with Header Pins ( www.analoglamb.com/.../) or the nrf51 on the Adafruit bleFriend...
Hello,this is Lee.I have a problem about nRF51822.
When I turn on/off the power 2.8V to it ,it hangs up
frequently.I check POR function,I found that the residual
voltage...
hi,
i'm using the 32KHZ external crystal and i didn't find any free space in my PCB to put the crystal in the same side with the nrf chip, so the only solution that i found...
I am trying to implement a bootloader with rewrite protection on nrf52840 with SDK: 14.0.0.
But it seems that there is no flash write protection registers in nrf52840.
So...
