Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi !
I work for about a year with a nRF52832 custom board without problem and recently I add a bootloader (with success) on the firmware.
Now I can't connect through...
My application is based on ble_uart_app. I want to integrate the DTM so that the nRF51 will be in RF test mode when it receive command from UART. However, I found that the...
Hi all,
We're going to implement floating point agorithms on the new chip which has a FPU (cortex M4F). with the 64MHz system clock, how many flops can we have? I could not...
Hello.
I use nRF52 & mpu9250.
I want to use dmp.
But now it's not going well.
Now, there is no error,but fifo_count doesn't change after fifo_count became 512.
I...
Hi,
sometimes not always, the function peer_id_is_allocated return false and this causes an ASSERT of device, because a NRF_ERROR_INVALID_PARAM is returned by pdb_write_buf_get...
Hi,
We're using nRF51822 and in the future we'll use nRF52832.
We do use bluetooth, but as far as I know, we don't use encryption (code is based on the HRS example, and...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
Hi
I migrated from SDK11 to SDK12/13.
In SDK11 I already had avaiable a softdevice to use for ble_app_uart peripheral.
In the new SDK I have to build the softdevice but...
I'm trying to understand example "ble_app_hts" how after advertising make a connection. I didn't see in code any call of function "sd_ble_gap_connect" ? how is made connection...
I use the nRF OpenMesh from the GitHub. ( https://github.com/NordicSemiconductor/nRF51-ble-bcast-mesh )
My mesh network just has two mesh node, node A and B.
I made A...
Hi everyone!
I want to work with two UART interfaces in my nRF52DK, in one hand, I must receive data sended by one cable which converts USB to serial, for this I use this...
Hello,
I caused a hardfault error and triggered the HardFault_Handler in "hardfault_handler_gcc.c". But instead seeint its source, I could only see the message no source...
