Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi everyone,
I'm using SDK 12.2 on nRF51822. Trying to get the buttonless dfu app example to work.
Here's what I do:
Compile buttonless dfu app.
Generate settings...
Hi,
I'm new to python and also the NRF51 dongle. I need to build a python script to connect my NRF51 dongle to a BLE device without using Master Control Panel. I tried using...
Hello,
i a have a problem debugging application with bootloader installed. I work with GCC for the application.
What is happening is the following:
If i program application...
Hi,
i used the SPIM example to create a connection with my ads1256. on my breadboard it worked properly. now i switched to a layouted board and every SPI pin is working...
Hi all,
I am using a J link to program a NRF52 via keil. It is successful but, every second program it fails with a Flash timeout error.
I am programming the application...
Hi,
I am trying to secure DFU on SDK 11 (NRF52). Would you please suggest if there is a way to secure firmware on old sdk, without upgrading to sdk 12+?
Thanks.
Hi All,
At the moment, I have three nodes and would like to configure one node as an end-device and the other two as routers. Using CoAP, the simple_coap_server is used...
I am migrating from nrf51 to nrf52. Using SDK12.1
On NRF51, I used the PWM Library to use 2 buttons on the DK to dim up or down onboard LED1 (called OUTPUT_LED).
It worked...
We are attempting to perform an OTA and as such want to transfer a large amount of data as quickly as possible.
When I attempt to transfer the data with connection intervals...
Dear Nordic team,
We have been working with SDK 8 and Softdevice S110 so far. We would now like to have the DFU using OTA for our product. I am looking for SDK versions...
Hallo Community,
I am new with Nordic chips, now Im trying to develop a BLE central, then i took the BLE_CENTRAL BLE_APP_UART example to start doing it, the SDK is the...
hello,i am using nrf52 DK.I was testing ADC example code .I am giving acq time is 3microsec .I want to find the total time is taken to sample adc for one sec.In data sheet...
I used S130 peripheral nrf51822 - nRF5_SDK_12.1.0_0d23e2a
Master Console Panel connection ok, and bond click error - >
BTLE_CONNECTION_TIMEOUT
I debug in my application...
Hello,
I'm having trouble with my nRF52. The power consumption is around 2.17 mA when sleeping. I'm using the softdevice 4.0.2 enabled and using the sd_app_evt_wait and...
Hi,
I am testing the current comsumption of nRF52832 using the original code of "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\ble_app_beacon ".
The peak TX current I...
