Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
we are trying to get the psa attestation on the nrf54l15 to work. We have tried config options for hours but CONFIG_TFM_PARTITION_INITIAL_ATTESTATION always gets 'n...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
When performing a OTA update with RPA enabled, the dedicated DFU app, nrfconnect app, and nrfutil.exe fail because after the buttonless bootloading has been enabled the device...
Hi Nordic Support,
I recently purchased two nRF54L15 development kits from Mouser Electronics. While one works perfectly, the other one appears to be completely dead out...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hi Nordic Support Team,
We are working on an nRF5340-based application using the nRF Connect SDK and would like to implement FOTA for both the application core and the network...
Dear Nordic, i have started my application with toolchain & sdk both v3.3.0, using custom services & charachteristics, with BLE advertising @500ms interval works fine. but...
Hi all,
Using two nrf54l15DK boards, v3.3.1 ncs, and ipt_initiator and ipt_ reflector demos without any modifications, in a testing environment at a distance of 5.1m, there...
Hi,
Using nRF Connect SDK v3.3.0, Toolchain v3.3.0, nRF Connect for VS Code 2026.7.2128, and J-Link V9.24a, I see the following errors when flashing a custom board connected...
Hi,
I am working on a Zigbee coordinator based on nRF52840 using the nRF5 SDK (ZBOSS stack).
My network includes up to ~50–60 devices (both mains-powered and battery-powered...
i would like to implement multi pairing connection of 20 peripheral device by single central mode. Is it best solution to adopt multi NUS sample S/W in GIthub?
Hi!
I am using nRF9151-DK, enabling UART1 and using CONFIG_UART_ASYNC_API.
The build is successful, but the problem every time i connect a flashed kit with this binaries...
Hi,
My central device is running into Bus fault when continuously sending data to multiple connected peripheral device and any of peripheral device got disconneced. Issue...
Hi everyone,
We are using the nRF52840 and nRF54L15 in our designs. We want to perform board validation before an image swap in MCUboot to ensure that the incoming image...
Hi everyone,
I’m currently evaluating whether it is practical to use the nRF9151 DK together with the nRF7002 EK in the same project.
The goal is to use the nRF9151 for...
