I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
My project: I am developing a system consisting of a central and up to 20 peripherals based on the Multi-NUS protocol. Toolchain and SDK : NCS v2.6.1. Development target:...
Hello,
I have a project for the nRF52811 using the nRF Connect SDK. As I understand, it’s not recommended to modify the main .dts file directly; instead, changes should...
Hi Team,
Problem: I'm working on a project using the nRF52840 and nRF Connect SDK 2.2.0. I need to transfer some files from host over UART and store them in LittleFS. I...
We are experiencing interruptions in the audio, with noise similar to popping sounds.
When observing the waveform on the spectrum analyzer during the audio interruptions...
Hello I am trying to build the Zephyr mesh distributor sample on the nRF 52840 dongle It builds and runs just find on the nRF52840 DK But when I try to build for the dongle...
I made a custom board And I am running the segger example ble_app_blinky_pca10056_s140 But Even if I run log_init();, it returns error code 5 And even if I run timers_init...
Hi,
I have updated the device application firmware from nRF Connect SDK v2.6.1 to v2.7.0.
The firmware was working fine in v2.6.1 without issue. But the same firmware...
mcu: nrf5340
board: nrf5340dk_nrf5340_cpuapp
sdk: v2.6.1
When I configure CONFIG_BOARD_ENABLE_CPUNET to enable cpunet, there isn't an issue. However, when I configure...
Hi, I have been trying to use my esp host mcu with nrf5340dk as a controller.I am using the hci_uart application with CONFIG_BT_LL_ACS_NRF53 =y to include le audio support...
Hi All
I am experiencing an issue with the nRF DFU app (v2.7.0) on devices running both Android 11 and Android 14. The issue occurs when I attempt to perform a DFU update...
Hello,
I want to run mass storage on my custom board with the nRF52833 and W25Q512JVEIQ. I have reviewed the mass storage sample (ncs\v2.7.0\zephyr\samples\subsys\usb\mass...
Hello,
I have a custom board with an nRF52833 and a W25Q512JVEIQ, which communicate over SPI (not QSPI). I successfully accessed the W25Q512JVEIQ (executed my own read and...
Hi, I am using nRF52832 module BL652. I want to measure the battery voltages of a 9V battery. What are the best possible resistors value to measure voltage of such battery...
