Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi, I have an issue with nrf52DK, I cannod flash new version of my software. I have an error in VS Code:
* Executing task: nRF Connect: Flash: Aurora-nrf52/Aurora-nrf52...
Hello,
I am using Nordic nRF Connect SDK v3.1.1 and nRF5340DK board. My project is based on the project: GitHub - nordic-auko/nRF5-ble-timesync-demo: nRF52 clock synchronization...
Hi,
Has there any good course or training you recommend developing with LE Audio Development Kit either through Nordic official training or your preferred training program...
We observed a problem with our three different prototypes:
When there is only 5V-VBUS connected, the npm1300 does not ramp uo its voltages properly. The voltage rises up...
Hi there!
May I know how to have UART00 on P2 like what is shown below as I wanted to have higher speed.
Is it the same as other UART assignments on P0 and P1?
Thanks...
Hi Nordic team,
I'm currently testing the nRF9151 DK with a Conexa IoT SIM card in the United States (Philadelphia area). The board is flashed with the Asset Tracker v1...
Hello,
I a doing a ticket because I don't understand why my dht sensor doesn't fetch with my nrf54L15DK board.
Here is my overlay file :
/*
* Device Tree overlay...
Hi,
I'm building a small Matter device and I'm in the very early stages of prototyping.
I'm using a MinewSemi ME54BE01 module on a custom PCB.
The development kit from...
Hello,
I am developing a project with the nRF54L15 and would like to obtain recommendations for specific part numbers of crystals compatible with the reference layout. ...
Hi,the Nordic team
I found that I couldn't set the FeatureMap attribute in the occupancy sensing section within .zap. How can I set it then?
the borad:Nrf54L115
the...
Hello all,
I am working on a project with 2 nrf5340 Audio DK's, and I have been working for a while now on getting myself familiar with the audio application, but I have...
Hi,
I'm trying to run the zephyr/samples/drivers/adc/adc_dt example on the nRF54L15 DK .
I modified the board overlay file zephyr/samples/drivers/adc/adc_dt/boards/nrf54l15dk_nrf54l15_cpuapp...
