I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I am trying to nrfutil to execute dfu over BLE using nrf52 dk and nrfutil. I have no problems when I try to use nrf_connect mobile app, but I want to use nrfutil desktop...
I want to write my application logs to the flash. I am following this tutorial which is for nrf52: https://jimmywongiot.com/2020/02/24/print-log-flash-log-crash-log-on-nordic...
I want to change the GPIO settings for the pin P1.08 but in the register description (nRF52840_PS_v1.2.pdf) there are only the names and offsets for the pins from P0.00 to...
I've been looking for a DC Motor controller example (for nRF52840) but without luck. Some other users have referred to such an example so I figured it should exist.
Anyone...
I am using SPIM4 with easyDMA in list mode to read a set of registers from an SPI device, and everything seemed to work great until I attempted to use the double buffered...
For some reason I can no longer compile any Zigbee examples.
The errors I am getting are below.
I have no idea what the issue is and I can't find any resources to help...
Dear sirs,
Here we've faced with the issue about logs output, could you please help?
We need to use two CDC_ACM devices on the board: one for shell and printk() output...
Hi!
I'm developing a peripheral device using nrf52840 to communicate with our android developed app. I'm testing the latency between connections of device. the configurations...
Hi, I need to estimate the power usage (so looking for TX and RX duty cycle) for the NRF52 during operation.
We will be connecting to a heart rate strap, and recording...
Hello - our certification lab is using the radio test example in order to perform their testing. They claim that the lowest channel they are able to set within the example...
Hello,
I am using nRF52833, nRF Connect SDK v1.5.0.
In v1.5.0 there is one new example i.e Zigbee NCP. ( Zigbee: NCP — nRF Connect SDK 1.5.0 documentation (nordicsemi...
I'm trying to update the advertising data using sd_ble_gap_adv_data_set function but it's not defined in sofdevice s140 v7.2.0 , it's defined in v5.0.0-3.
Please how can...
I installed NRF connect SDK v1.5.0-rc1.0 through toolchain manager.Open SES and create a project with open NRF connect SDK project.An error occurred.'create_nordic_project...
This function succeeds only when Thread protocols are disabled. my question is: if the Thread protocols are enable,what should I do to disable them ，now what I do is:
"otThreadSetEnabled...
