I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi,
I'm using nrf52833, flashed by using Jlink SWD programmer. I have no probleme to re-programmed 2/3 of my board.
But the hird gave an error. The strange things...
I am using the gazell protocol of nrf52840 to achieve some functions,but I don't know how to understand the protocol code deeply,anybody has advice or flow chart or relevant...
I want to implement noise sensor based on PDM (pulse density modulation) , But I cant found any PDM driver or API based on Zephyr , I used MP34DT05(st semi-conductor).
So...
I have nrf52832 radios communicating with each other 100%. I have a nrf24l01p that is the 'gateway' to which the nrf52832 sends dump data. I can communicate with nrf24 and...
When i start the nRF mesh app, it crashes immediatly. What do i need to do? I re installed it a couple times and i rebooted my phone a couple times.
The phone is a samsung...
Hi,
I am developing firmware both nrf52 and nrf91.
in nrf52, I activated BLE, usb and uart. Uart communication established between nrf52 and nrf91.
in nrf91, I activated...
Hello, I have done customized board using nRF52832 and when I try to flash code using nRF52 DK(Jtag). I can able to control led's using customized board. But Bluetooth is...
I am using the gazell protocol of nrf52840,how to use broadcast radio mode from host to device based on the gazell protocol ?or can I use the gazell protocol to make it possible...
We have an neural network running on a 52832 using the floating point unit. We started encountering FPU exceptions so we enabled the FPU IRQ to identify which specific instructions...
Hi everyone,
I want to create multiple USB instances using only one nRF52840 dongle. I want to implement one CDC ACM class instance and another one instance that has two...
Hi,
I have a problem with floating point types on nrf9160.
I get an exception when I get to a simple floating point assinment:
void f(int i)
{
float x;
x = (float...
Hi everyone!
I'm new using Nordic Semiconductor products, I have a Nordic Thingy 91 running Asset Tracker application by default.
I want to test only specific things first...
I was thinking of using the nordic thingy:91 for monitoring purposes in seismic areas.
To this aim, I would need to have some sensors deployed in the environment which:...
Hi,
I need to use nrf_dfu_settings.c to detect external firmware in Bank 1 during application boot. I also need to use Falsh Data Storage to save application parameters...
