Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi, I am attempting to flash various bluetooth samples onto the nRF5340pdk, and I am getting errors on multiple levels.
First, when I attempt to build the samples (I have...
Hello, I am trying to load some example on my nRF52840 dongle. I am developing without using a board but only the dongle, SEGGER and nRF Connect 3.6.0 .
Following this guide...
Hi everyone,
I've noticed in SDK examples such as the ble_app_hrs that call APP_ERROR_HANDLER after softdevice API Call.
What is the reason for this API call?
Any side...
Hello,
I am working on ble_app_uart example on nRF52840DK.
According to the documentation, when the device is advertising, the LED1 should blink. But I am not able to...
Hi all,
I was going through the release notes of the S132 V7.2.0.
Under known issues, DRGN-10340 states the following:
"The BLE_GAP_EVT_SEC_INFO_REQUEST event will not...
Hi, I am developing a SDK 17.0.0 based iBeacon application, and I see BLE library available for advertising.
I went through the ble_advertising_init API and found the parameter...
Hello, when I run OpenThread CLI example in NCS 1.4.0, I get the following message on the serial port:
E: Failed to store setting 3, ret -22
I am using the nrf52840 D...
I'm now using nrf52810 sdk16 for product development, but we need to pair bind. So pair bind, generate short-term and long-term keys where I can find it? How can I generate...
Hi everyone.
Not knowing exactly where to go to get help I am taking the liberty to ask my question here hoping that some good hearted soul might help me. The device manufacturer...
I created a project on nrf9160, which connects many peripherals, including SPI,I2C,UART. According to the specification, nrf9160 can use up to 4 sets of serial peripherals...
Getting the example programs to work from the NRF52 SDK can be a very daunting task. The big problem is that there is virtually no documentation included in the samples themselves...
Hi; I'm trying to develop an application with the nrf52840 as a co-processor. We decided to use the nrf52 as a SPI slave and a SAMD21 as a SPI master. I set up a quick Arduino...
Hi,
I have a question about the tolerance on the VDD voltage. In the datasheet it says: "RF 3GPP compliancy requires 3.3V."
I am wondering if there is more specific...
