Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hi everyone !
I have 3 services and 13 characteristics in my project. Until today, 3 characteristics were working fine. But i added rest of the characteristics and my project...
Hi all,
I am currently using Pyaci serial to establish and test BLE mesh network, and it work fine.
The further step we want to do is to create a duplicated Provisioner...
I have a Thingy52, but no DK. I would like to know if it is today possible to upload a custom firmware only using OTA (no DK), eventually starting from the Nordic Thingy app...
Hi,
I'm trying to transfer data between an nRF52840-DK and an Android phone which has nRF Connect installed on it and I can only reach about 40kbps (that is kilo bytes per...
Hi, I am working on installing the pc-ble-driver-py library and building it to run an application for a nrf52840 Dongle over serial port.
I have followed github.com/......
Hi everyone!
I have a nRF52840 dongle and I am trying to run python examples from pc-ble-driver-py. The dongle is connected to a PC running Ubuntu 18.04. The dongle is flashed...
Hi,
I am using the SDK 11 on nrf51822 I just merged the TWI sensor example and the BLE UART example. Both work together but the softdevice seems to be slowing down the twi...
Did anyone configure correctly VS Code with nRF Mesh example?
I did install CMake on my computer and download CMake extension to VSCode. I am working on Windows.
I did...
Environment - Mac - nrf tag; 1.1.0 - modem fw: 1.1.0 - DK 0.8.5 - debugging by SEGGER RTT The program polls SMS for a certain time and if SMS is received, it reads the messages...
Hi.
I am trying to update soft_device version 6.0.0 to 7.0.1.
I read that because of the major version change (from 6 to 7), i must update the bootloader as well.
I...
Hi,
I am prototyping with the the THINGY52 using nRF Connect.
I am using the services available to drive the MOSFETs on the expansion connector P4 through the services...
Hi,
I would like to debug the code which is in Nordic Thingy91 by using nRF52840DK.
Is it possible to use the debugger in nRF52840DK for Nordic Thingy91 ?
If it is possible...
Hi,
I like to understand what SBs should I cut, what switched should I use to measure the SOC current only with PCA10056 board. I use the Otii Arc device to supply power...
Hello,
I'm working on NRF52832 based module BMD-301
for same i'm using SDK16 Segger Embedded Studio
The thing is
when uploaded ble_app_alert_notification example it...
Hello,
I've tried to convert the mesh light switch server example from NRF52840 DK to Dongle following this post.
Unfortunately that doesn't work.
I've changed the BOARD_PCA10056...
