I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
Hi
I am working on nRF52832 SOC and developing hardware modules.
we are using nRF5_SDK_15.3 and SES
we developed one new hardware module with nRF52832 SOC
and we testing...
I am trying to develop a program that can read the RSSI from the nrf52840 dongles without using the RSSI in the BLE app.
I have looked through the example code that is given...
Hi,
I designed a gateway that includes nrf52832 which receives beacons and sends it to other processor through uart, and this processor sends beacons to the server. Well...
Hi
We have managed to change our firmware BLE settings in order to be iOS compliant
However Android side we notice that it is more difficult to scan and especially...
I am using the v1.0.0 sdk at_client sample project with the v1.0.0 LTE Link Monitor on an 0.8.2 nRF9160-DK board. I have upgraded the modem firmware to 1.0.0.
The AT%CMNG...
I am trying to transfer data from a USB to serial converter board (called board A) to the nrf5 board (called board B). I made the connection over a bread board, the transmitter...
hi i'm use nrf52dk
and segger embedded studio
also i'm mcu beginner
The value was obtained using a magnetic sensor.
now i want using the ble
Now we want to send...
Hi,
I started working with nRF9160 and took AT_Client and added support for my own commands. Additional to that I added HTTP example to it and they are working great together...
Hello,
i have a very easy goal, i want to generate a hex file which combines all parts and flash it via nrfutil or something like that onto the device.
I followed a few...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hey , i'm using nrf52832 with SDK 14.2 . I'm trying to send 3-axis accelerometer data through BLE . Is there any example for SDK 14.2 to achieve this ?
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As shown in below snapshot I am just doing below...
According to the blog below, hardware design of nRF9160-SICA has been fixed on May 31st. https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf9160-development...
I am designing a pcb just the nRF 52840 MCU. The design of the PCB is based on the reference design from Nordic. When ordering the PCB I came across a problem that the vias...
I have 4 gpio inputs on the nRF52840 working and sending these states over the BLE. I tried to add a few more gpio inputs but I get an error =4 which I think is NRF_ERROR_NO_MEM...
