Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Using nRF52 with SD 132 3.0.0.
Peer manager uses fstorage to store information.
I need to be able to specify the address range which fstorage can use.
Is there a configurable...
Hi,
I have problem with both functions sd_ble_gatts_value on central device.
It works on peripheral, because there is my characteristics definition.
Now I have to read...
Hello,
I'm developing a BLE Application where I use the peer manager. My Goal is to use direct advertising after disconnection if a device already has bonded. But every...
I am using the SAADC on the nRF52832, SDK12.2.0, with it set to 12 bits and low power mode. I have enabled five channels which I run blocking nrf_drv_saadc_sample_convert...
Dose this capture from the Nordic Specification means that to read bytes from SPI i need to send before. Each byte i send i get a byte!!!
MLy case i have read only sensor...
I am using the nrf52832 with the s132 for a project in which I have a frame with 24 bytes that need to be transmitted through BLE.
I have followed the tutorials and I have...
Hi,
First I'd like to salute the great work done by you Nordic people for those open source and hardware.
I just installed the SDK 10.0.0, S120, gcc-arm toolchain, configure...
Hello, I'm a beginner with the BLE technology and nRF52 is a good tool to start with it.
Currently, I have a setup that allows a Raspberry Pi and an nRF52 to communicate...
Hi. I have a problem with programming brand new chips nRF51422.
I have connected: Vcc (1, 12, 35, 36), Gnd (33,34,13), Swdio (23) Swdclk (24).
christal on the board:
...
I had downloading many versions SDK,from 10.0.0 to 12.2.0.But when I Program SoftDevice then download the examples,such as the path:
nRF5_SDK_12.0.0_12f24da\examples\ble_central_and_peripheral...
hi,all.
when i first time connect nRF52840PDK to PC, and open nRFgo Studio, but encounter this problem:
no device detected.
screenshot:
I click recover button many...
I want to send several packages in one interval from my iphone to 51822(s130).But the demo ble_app_uart can only receive 1 package per interval（ipone6，lightbule，writewithoutreponse...
I want printf the date and time when compiling code.
But I drag on this error:
SEGGER_RTT_printf("%s %s.\r\n", __DATE__,__TIME__);
compiler says:
It's strange...
Hi engineer,
I found that the SAADC current is increased after the SAADC function opened, then my processing method as below:
1,I close SAADC function after sampling...
Looking for the OpenOCD equivalent of ""nrfjprog --rbp all"
Looking at the commands for OpenOCD they have a "flash protect" command, but it doesn't appear that's quite...
