Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hi,
My application receives assert error from stack. Source file name is src\ll_master.c, line number 831 and error code 0xDEADBEEF.
What this error signifies?
R...
Hello,
In my application I'm using SDK 8.1 with the s110 SoftDevice. In the new version, the pstorage modules have been separated and you need to choose between them.
...
Trying to see how much time my code consumes, I tried the naive approach, calling clock() in the beginning and at the end and comparing the values.
But when I include clock...
I am using the BLE Scanner app on Android to check that my device works.
I have 2 similar problems :
on one device, I can read all characteristics except one. This has...
Hi,
Im trying to use this example to send serial data from GPS module via BLE:
github.com/.../ble_app_uart_low_power_slave
I have disabled hardware flow control since...
Hi
I tried gateway and LED_mesh examples. It worked well. But, I found some issues as below.
When I tired MCP windows application on laptop with PCA10031 dongle...
Hi there,
I am using the nrfjprog to flash the nrf51822 via a J-Tag programmer. Here is the command I used in the command prompt:
nrfjprog --eraseall --programs softdevice...
Haw can I configure ble_app_ uart examples for bonding using? I want to connecting, transmit and receive data throw the UART only with 5 fixed devices.
Hi,
I updated to softdevice 8.00 recently, and found something different with softdevice 6.00.
When trying to program the new softdevice hex to the chip using nrfgo studio...
Hi,
I am using nRF51822 chip.
I am using the softdevice s120_nrf51_2.1.0. On top of that i am flashing the HRM central example given in the SDK nRF51_SDK_8.1.0_b6ed55f...
Hello, I'm fairly new are Nordic and have inherited a good project from a departing coworker. We are using Keil uVision 5+nRF51822+BLES110 softdevice.
She explained her...
Hello,
As mentioned title, when using printf with softdevice, "Stopped by a vector catch" occurred.
I am using my custom board(nRF51822 and s110).
And I am using IAR...
Hello,
When i try to set value of the gpregret using sd_power_gpregret_set and clear functions in on_write callback function, cpu gets stuck (i check it in debug mode). Can...
Hello
I'm trying to communicate with an sensor over the TWI HW interface during a BLE connection with the S110 soft-device, and every time I try to use the TWI bus the...
