Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
I made a DFU Bootloader for my nrf51822 that waits for two seconds before starting the application, so I have time to connect and flash.
That process was working with the...
If I set two separate UUID scan filters as below:
Is it possible to discern which event triggered the filter match?
At the moment on the scan_filter_match callback,...
Hello,
it's a nice concept to include sensors via the device tree and simply enable them in the project file. But I feel like I'm losing control of the sensor a bit. I don...
Hello nordic. I've been using the PPK2 to measure the current draw of the nRF9160DK. However, spi peripherals are not included in these measurements. I was told that if you...
Hi
I´am pretty new with the nRF connect sdk. I want to check the features from BLE long range /coded phy.
In the past I have allready worked with the ble_att_mtu_throughput...
hello Sirs
How can I put nrf5340-sdk in to extended mode to transfer 250 bytes of data over BLE radio?
the sample code I am using is Peripheral-uart example code.
Excuse me:
I want to implement nrf52833 run FreeRTOS，The nRF52840 project in nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_hrs_freertos\pca10056\s140\ses can only...
Hello All,
I am using NRF52833 in my project. I am also using RTOS in the code. I was previously working on NRF52840 but now I have migrated to NRF52833. I have changed...
I'm new to using NFC.
I've tried downloading a few NFC sample programs to my nRF5340-DK board and playing around a bit, but I ultimately want to implement something like...
We are using nordic SDK 16.0.0 and mesh SDK 4.2.0 with a nRF52840 chip.
Our products already have the provisioner/provisionee and config client/server implemented, based...
Hello, I use nrf9160dk, ncs v1.6.1.
I'm trying to use both AWS IoT to store some data from the DK board, and to connect to nrfcloud for AGPS data. I don't have any previous...
Hi All,
I am beginner in development on Nordic product.
I am using sdk v1.5.1 and nrf5340 for development.
I want to add open source library libcorrect.a for Forward...
Hi.
i use
i call i2c_write() and if the buffer is large(8kB) i get error in i2c transfer -5.
i go deeply and found that it is due too error -11:
If i step into...
