I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Hi,
I know that there are different ways to set up the radio, but generally speaking, is there a general practice for how commercial devices' PHYs are set up when advertising...
Hello people, Honestly this is a problem more related to a Raspberry Pi than the nRF52832 but I'm getting same difficulties here so I will explain my situation. I have been...
Hi
I just want to read the Device Information Firmware revision string from a known Peripheral on my Central.
I Use the PCA10028 with SDK 12.3 and Softdevice S130...
Hello to all,
i've developed some application under 3.2.0 SDK. Now I want to port my application on new 4.1.0 SDK but a I have found a relevant issue.
Before migrating...
In section 6.3.2 of the NRF52840 dongle user guide it describes how to modify the board for use with an external, regulated power supply. Once those modifications are made...
In order to implement the central roll, I put ble_app_uart_c on ble_app_multilink_central and joined them to communicate with the pc.
What I did
1. Add enable in ble_app_uart_c...
Hi ,
I need to start my application using sdk5 16.0 version, which should have custom ble servivnced and dfu feature.
After getting some trouble with zephyr os, i decided...
I have used an example in the sdk 15.2.0 Pin_change_int_pca10040 and added 2 header files and 2 C files extra to this project. I have cleared all the error which came while...
Our hardware has Winbond NAND Flash chip connected to the nordic MCU(nrf52840 /nrf5340). However QSPI cannot be used as nordicSDK doesn't support NAND Flash.
I understand...
Hello,
I am using the Power Profiler Kit connected on top of an NRF52840-DK
I am using IAR and using IAR's J-LINK plugin to program/debug an application on the DK. However...
I am trying the example project ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\l ight_switch' and ' ..\nrf5_SDK_for_Mesh_v4.1.0_src\examples\ dimming' available in nrf5_SDK_for_Mesh_v4...
Hello,
I'm experiencing NRF_ERROR_INTERNAL from a call to pm_peer_new(). While further investigating into this, it turned out, that the p_bonding_data parameter was checkt...
Hello! If possible, I ask you to answer a practical (technical) question: how long does a typical process of establishing a communication session (“handshake”) in the BT5...
Hello, we are creating a device on an nRF52832. I started our project based on the examples/ble_peripheral/ble_app_uart project, which worked fine. However, I needed to modify...
