Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi,
I have recently developed a simple custom board with the use of the BL651 module to have a dev board for myself. Although the schematic diagram is simple and the PCB...
I have nRF9160-DK bought fairly recently. The IMEI is printed on a label on the back of the board. But, there is not PIN. Registering the board as an LTE device on nrfCloud...
Hey all,
I was curious to see if anyone else is seeing the same problems I have with DFU.
I'm currently running SDK 15.2 and version 1.8.8 of nRF Connect on iOS. When...
Hello,
Previously I was using nRF52 SDK V11, printf did print properly and provided linefeed with '\r\n'.
Now I started using SDK V15, printf is no longer supported and...
I'm developing a nRF52832 based HID device and I'm at a bit of a loss as to why it isn't working on iOS. The device works as a keyboard fine on macOS, and it connects and...
Running nrfjprog 10.3.0 on macOS 10.14.6 (18G87) with an nRF52 dev kit
Occurs on all 10.x releases of Nordic command line tools. Other switches such as -i work.
edit...
Hi, I installed the nRF connect SDK, but get the following problem when trying to open the asset tracker project:
If I press ok, I see this:
Any ideas about what...
I use nrf52832.
Document written,
-------------------------------------------------------------------- RX current comsumption is IRADIO_RX0 Radio RX@1Mb/s BluetoothLowEnergymode...
Hello,
I'm trying to use raspberry pi to program nRF52832 on mass production. Because it's easy to do some test job with raspberry pi.
But there are still some issue I...
I want to achieve: 1. Mobile application networking with multi-lamp mesh 2. After mesh networking, many smartphones control all lights independently through proxy nodes. I...
Hi,
We are using nRF52832 based module on which we are using HCI over UART functionality with the help of Zephyr(v1.14.0) SDK to find the nearby beacons via Bluez stack...
Hello there,
So we are working with a sensor that needs to receive a pulsed voltage, so we are using a PWM signal from our nrf51-DK applied to a transistor based circuit...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the nRF5 SDK v15.3.0 and modified twi_sensor_pca10056 program...
Dear support,
We have built a ble mesh network running the light_switch_client/server application (mesh sdk 3.1.0). We are using the Android application for provisioning...
