Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
I've been attempting to optimize my scan and connection intervals in order to maintain the highest percentage of time scanning while maintaining connections, following the...
Hi,
I am developing a Linux PC application (central) connecting with nrf52840 dongle with s140 v7 flashed on it (for long range support). I am using pc-ble-driver v4.1.1...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
I have 3 devices that can communicate via UART: 1) nRF52840-DK (PCA10056) 2) FTDI (set to 5v logic) 3) BLE HM-19
I'm using the example in ./nRF5_SDK_16/nRF5SDK160098a08e2...
Hi,
In gps sample, the prj.conf file is:
And I can use Putty or Serial.app (on my Mac) to view the output
In our application the prj.conf file is the following:
...
nrfjprog is reporting "Cannot connect to J-Link." while trying to erase on MacOS Catalina
Board used to work properly, but attempting to re-connect after a wipe of my MacBook...
I am using the nRF52840 dongle (pca1009).
I have read from some digital inputs successfully, but am not able to read from P0.02.
I set it up as an input with the following...
I am new to BLE and this question may seems little unusual.
My goal is to connect two nrf52 together over BLE and when i press a button in central device , a write event...
Hi!
My goal is to sample an ADC channel with 10 kHz sampling rate and acquire 2000 samples in one samples acquistion and then return to lowest possible power state. This...
Hi,
I received a Thingy91 from a colleague who orderd it shortly after hitting the virtual stores but didn't do a lot with it. I got it on my table and started to work on...
Hello,
SDK 15.3.0
s140
nrf52840-DK
IDE: SES
I am attempting to use the LPComp + NRFX TIMER 4 to count the rising edge of a signal, the timer is being used to time...
I am currently evaluating the nrf52840 for a possible future application which is based around BLE and should also provide a HID Generic interface to perform communication...
hi..I have merged the saadc with ble_app_uart and i have added all the respective files and enabled the ppi, saadc everything . while i am running the code ,getting unknown...
Hi,
I noticed something strange while developing with the nRF9160 modem's RTC. Here's the sequence of events
Connect cellular
Get time from NTP server and initialize...
Hello nordic
I'm running iot icmp example on my nrf52832.
The border router is Rapberry 4. root@raspberrypi:/home/pi# uname -a Linux raspberrypi 4.19.71-rt24-v7l+ #2 SMP...
