Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hi,
I have created a custom board with an NRF52832 chip on. Either programming via ULINK2 or the DK PCA10040 is no succes, board won't be recognized although it is powered...
Hi,
During preparation of development environment it was figure out that link to nRF5x-Command-Line-Tools-Linux-x86_64 is invalid(http ec 404).
BR,
Iurii
In this case, when I change values in the "User memory", is there any API call or other action required to advise the SoftDevice that the data has changed?
Only the values...
Hello.
C21, L5 and C22 are part of antenna matching. And, L6,L7,C23, C17,C19,L4,C20 they suppress the harmonics and spurious responses and match the chip to 50 ohm. R19...
Hello,
I am trying to setup the DTM to evaluate our product. I am using shielded boxes and following the setup from application note 34:
I am unfamiliar with this...
Hi all,
I added ble central multilink example with ble_app_uart_c code, i am able to compile code successfully, but not able to run this code on board due to this error...
Hi!
I am developing a project where an NRF52840 DK is receiving data from the environment using BLE. I can observe the received data using NRF_LOG_xxx() command in my...
I'm trying to use the PA/LNA control feature in S112. However I only want this to be enabled when under specific conditions/configurations at runtime. So I need a way for...
There are 6 channels per the SDK (nRF5_SDK_15.3.0_59ac345) and the product spec for nRF52840 but I cannot seem to get channels 4&5 to do a compare or capture. Using Keil's...
Anybody got any hints at how to get Zephyr to work on the nrf52840 PCA10059 dongle?
After many struggles, I was finally able to compile Zephyr's sample/bluetooth/hci_usb...
Hi there,
I am trying to get I2C communication up and running with the nRF52832 (specifically configuring the nRF52832 as a master to communicate with 3 slave devices),...
Hello everyone,
I am developing a temperature and gas sensor for indoor environment monitoring. Due to the limitation of the bluetooth transmission range, I hope to add...
Hello, I am developping on a nrf52840-DK board and try to debug using a Black Magic probe. Software is based on softdevice, GCC build chain and Visual Studio Code with Cortex...
