Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi
I'm facing a Hard fault on the softdevice when trying to call sd_ble_gattc_write(). SDK15, SD140
I have a Multilink central connected to UART using app_uart. when a...
I have been doing a bit of searching and reading but I'm none the wiser.
I have a client that uses lots of BLE nRF51822 based modules made by Raytac Corporation in a classroom...
I am converting Arduino BNO080 library ( github.com/.../SparkFun_BNO080_Arduino_Library) to nRF52832.
Specifically, this is a function for sending a SHTP packet over I2C...
hi to all,
i had developed a device with NRF51822 wih S130 and i want to port my application to new NRF52840 soc S140 and SDK15, S130 has an structure that let me to limit...
Below are the symptoms, but it turns out the problem was quite simple: the device is not seem capable of scanning while at the same time being connected, unless you use a...
Hello,
I have a problem where the nRF52840 is not advertising. The code runs in the debugger but there is no radio signal. I've already sent the schematic and layout....
Is there an easy way to check what the current connection's agreed upon MTU is?
I'm connecting to random devices that all have different intervals and MTUs. I can't be sure...
When I use saadc to sample battery's power,the software restart ceaselessly.I use the steps as following:
1.void saadc_init(void).
2.void saadc_callback(nrf_drv_saadc_evt_t...
Dear Sir,
I am now using nrf51422 module (SRU532) for ANT+BLE application , i have used SDK_9.0.0_2e23562 and soft device s310_nrf51422_3.0.0. The problem i am facing is...
Hello,
I am using SDK 12.3.0 on nRF51822 development board and nRFConnect app to scan and connect the peripheral device.
When i changed Mouse icon by the GENERIC_THERMOMETER...
Hi,
I'm developing a simple software that records RSSI values from both the Central and Peripheral device, using nRF5 SDK 15, adapting from two of the provided examples...
I am trying to implement the example-code for the Eddystone example from the infocenter. I'm using the nrf51422 to flash code to the Smart Beacon (PCA20006 with nRF51822)...
I am using the Nordic 52840 CSP for my project. It is used for a asset tracking application. I used the nRF52840 QFN schematic reference for design. Since there is a difference...
Hello,
I am looking for the inband image frequency for the NRF51822. I have received a few different results and want to confirm what the value is if it is Low 1Mbps: +1...
Hello Nordic,
I have seen a couple of your reports and I am not sure how to read the inband image frequency. You have put frequencies in there (I thought values should be...
