Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
the project has a problem with DMA,the detail is:
on the board,NRF52832 and extern chip communication with i2c bus,the chip through a pulse wake up nrf52832,NRF52832 start...
I have NRF51822 Controller(custom board,S110) used to send some sensor data. i can able to receive data in android and ios. now i want to communicate to Laptop which has internal...
Hello Everyone,
I am new to nrf51822 (using S130). I made some custom service that accepts float numbers.
This might be noob question: I want to send float values from...
We are developing a custom ble service and profile however having printf makes our lives that much easier so we are trying to incorporate it purely for testing purposes. ...
Hello,
I'm trying to optimize my application :
I have a central (nRF52832 s132) which communicates for a short time to a peripheral (nRF51822 s130) and then disconnect...
Hi
I'm trying to register an fds_evt_handler() in SDK 14. I have several questions:
Should I be registering fds_evt_handler() with NRF_SDH_SOC_OBSERVER or NRF_SDH_BLE_OBSERVER...
Hi!
Is there any chance to get the Altium files for the nRF24L01 refmodule with PCB antenna? I found the files but for the SMA version and I'm trying figure out the same...
Hello,
This is Milav Soni from Teq Diligent,India.
I explore the nRF52 series Chip and nRF51 series chip.
I also explore some of your BLE video.
I have one question...
Hello,
I'm using SDK 13.0.0.1 to develop my project. For driver example, such as RTC, I can't see data log while I can see the data log for BLE example, such as ble_app_uart...
Hi @ all,
We discovered a bug in the Nordic TLS API, which only appears once a secure TCP connection that makes use of certificates is to be established.
The provided...
Hello All,
I'm developing a BLE sensor based on the nRF52832 which needs to do the following:
Use an (i)Beacon for the user to find the sensor with an App on a mobile...
nRF52832 has errata about gpiote as below.
3.29 [97] GPIOTE: High current consumption in System ON Idle mode
So I want to use PORT event for gpio interrupt, but PORT...
Hi all,
I programed hex file (blinky example) to nRF51DK via nRFgo Studio, and the board could work fine (keep blinky).
However, the nRF51DK will work FAIL (LEDs are not...
Hi,
I need to monitor voltage very frequently, have access to the latest value and also to have interrupt on low limit.
But I do not want to have interrupt on EVT_DONE,...
