I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
I am interested in optimising inputs for ADC measurement on an nRF52.
I have seen quite a bit about nRF51 but am unsure if this remains relevant for nRF52?
Hi!
I have an nRF52832 on a custom board. I managed to flash it through JLink and STLinkv2. But suddenly, I wasn't able to communicate to it anymore.
Openocd tells me...
Hi
The new signed DFU in the SDK12.1 comes along with a experimental buttonless DFU. There are a few bugfixes required to make it working, but the nRF Toolbox app didn...
Hi:
Recently, I want to use nRF52 to read or write some data from a flash chip(w25q128bv) by using spi, I've read Manufactures ID correctly, also, I have wrote a register...
Hello!
I need to interact with two J-Link debuggers, connected to the same PC at the same time. I would then read and write data to the devices connected to the debuggers...
Hi team,
iam using sdk 12.1.0 (ble_app_beacon) I want to advertise the battery percentage.Right now iam using the nrf dongle(it doesn't have cell coin battery) and flashing...
I am attempting to build some ptorotype code using SDK 12.2.0 and GCC and I just added calls to the app_schedukler library and to the saadc driver. I added the relevant source...
I always read 0 first time I call sd_ble_gatts_value_get(), the second time and forward I read correct value. Even if I call sd_ble_gatts_value_get() twice in a row the first...
Hello,
I generated a new project using the main.c of the example "ble_app_uart" from the SKD 12.2 for a nrf52832 and from there copying all necessary .h and .c-files into...
Hi DevZone
I am trying to DFU OTA a PCA10040 using BLE Secure DFU Bootloader from SDK12.2.0.
I can succesfully transfer the image i have made with nrfutil to my DK,...
Hi,
I'm working on integrating ANCS on our existing and futur products. I started to port the Nordic SDK example (12.x) and it seems to work fine on nRF52, which will be...
I am currently using SDK 12.1.0 and experiencing intermittent HardFault crashes in timer_list_remove() with the stack indicating the origin being a SWI0_IRQHandler call. ...
i have a setup with one NRF24L01+ as PTX and one NRF51822 as PRX
my problem is that the data sended ok and ack sended to NRF24L01+(i assume that by NRF_ESB_EVENT_TX_SUCCESS...
