We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi team,
Iam using (\ble_tester\examples\ble_central\ble_app_hrs_c\pca10028) this example.i want to get rssi from the advertising beacon.
Iam using this functions
sd_ble_gap_scan_start...
I see on your website that Bluetooth 5 throughput numbers are given in the graph below. And the following disclaimer is given.
"Net data throughput not including overhead...
I have taken a look the APIs which the S132 supports in nRF52 DK.
However i could not find the APIs that can initiate the channel map update ,feature exchange & version exchange...
hai
i have this code to save and read some data in flash.but the stored and read data are not same. always reads zeros. how can i solve that.........?
here is my code...
I'd like to be able to quickly update the advertising data using
sd_ble_gap_adv_data_set()
and at the moment I'm doing this via a bit of a hack, as I captured the advertising...
Normally, Raw data has TYPE (0x01), TYPE (0x09): device-name, TYPE (0X07): UUID 128 bits.
However, there are devices without TYPE (0x07).
Is this also a problem?
Communication...
Considering using an nRF52 module, I'm developing using EvoThings' native plugins right now. I don't think we have the resources to do IOS and Android native apps.
Has...
I have an application where my nrf52832 acts as a peripheral and I can connect to it without problems, but after some time like aprox 10 minutes when I try to connect to it...
Hi!
I have searched for this questoin, but not found anything useful. Probably I an not using a good search phrase.
How do I determine how much space is left on a nRF51...
This is a general question I will throw out initially, but I can get more specific if necessary. This is something I see a lot in my year or so of development with nordic...
SDK:8.1.0
Chip:51822AAHO
Hi,i use the nRF51822-PSV3.1 Schematic diagram.The chip set 4dbm tx power,
then i test the test point(C6) as follow,2402MHZ and 2426 MHZmax...
Hi,
I run the HID keyboad example, and a problem confuses me. I use the "lightblue" APP to connect the peripheral--"Nordic Keyboard", but the iphone appears a pairing box...
Hello!
I have been working recently with the PCA20006 Beacon board. The example we have tested is the ble_app_beacon that allow us to change the UUID/Major/Minor and go...
This may be a stupid question, but...
What value is BLE_GATTS_ATTR_LENS_MAX
Its mentioned a lot in the SDK, but I can't actually find a value for it actually defined...
