In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
I want to capture connection packets between BLE Master and Slave
(this part is easy) but also capture any advertisement send out by slave
at the same time.
Our BLE peripheral...
I brought up the Template example on the S110 for nrf51822 and as an exercise, attempted to add in the battery service. I just did a few simple things:
in main.c:
-included...
Hello, I want to using nrf51 dk with uart communication.
So, I want to know how connect both PC and nRF51 DK.
I've download with 5pin connector to USB.
In former days,...
hi,
i have meet an issue,when my pca10028 board was advtersing it can be found by the android app which provide by nordic.But it can not be found by my mobile phone.So,i...
I have compiled the bootloader and the application firmware with keil.
When I install the application firmware by means of the bootloader dfu ota.
The bootloader launches...
Hi,
Unable to locate the source code for "UART/Serial Port Emulation over BLE"?
The documentation for this is available in this link - developer.nordicsemi.com/.../a00072...
Hi, i try to understand how to use power down modes. But i have a problem in the example gzll_device_w_power_management of nrf24le1 sdk. Before enter register retention in...
I just started using RTT because I needed to trace execution through some ble events and the uart could not keep up.
It is very nice, but I am used to frequently resetting...
Hi all,
I'm trying to use the experimental ANCS example with an iPhone iOS 8.3. My Nordic SDK is 8.0.
The sequence is the following :
Flash the example on the dev...
Hi,
I'm looking at interrupts from three different GPIO-pins. I'm setting it up like this:
static void gpiote_init(void)
{
uint32_t pins_low_to_high_mask = INTERRUPT_1...
Hi,
I'm using device manager for bonding starting from a sample application in the SDK.
I see that the DM_EVT_CONNECTION is raised before the BLE_GAP_EVT_CONNECTED but...
Is there a way to prevent nrfjprog from disabling target power from the J-Link when programming? I've tried setting power on perm but to no avail, nrfjprog powers down my...
I would like to know the RAM usage of my nRF51822 application. I found this post discussing some of it, but there is no obvious conclusion yet. I am using Keil for development...
I am using nRF51822-QFAA_Rev2. S110 7.1.0, SDK6.1.0.
First, program bootloader, then program \s6310\s110\ble_app_hrs\arm\ble_app_hrs_dfu code.
I use Android nRFtoolbox...
When performing a DFU using the latest iOS nRF Toolbox I keep getting an "Error on init Packet Message:Operation Failed". The DFU works fine with the same firmware application...
