I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
If you clone nRF5-cmake-scripts , then switch it to the archive/sdk-16 it builds if you follow the build instructions.
What I'm wanting to do is adding the mbedTLS backend...
Hi,
I have a current project that is based on the nRf52840. This project acts both as a peripheral and a central. I have a need to update the firmware on a remote BLE sensor...
Hi,
I'm using a custom board which is currently under developpement usin nRF52810. When running DFU example for NRF52810, using secure_bootloader_ble_s112_pca10040e.hex...
I read this post https://devzone.nordicsemi.com/f/nordic-q-a/10668/rssi-without-connection
I want to know how large the RSSI value will affect the connection. Is there a...
Hi,
I am developing firmware for NRF52811, using SDK 17.1.0 and Soft Device S112.
I need to write a characteristic longer than 20 bytes. I thought it could be done with...
The bluetooth connection is automatically disconnected, and the reason is 0x3E. Is this related to the small RSSI value? I set the transmitting power as 4DB, and the RSSI...
Hello,
I'm exploring the nrf5340 controller with a Fanstel evaluation board (EV-BT40) I use the SDK V1.7.1 with vsCode.
Used example "Bluetooth: Peripheral LBS".
Connecting...
I've recently flashed USB CDC ACM example to NRF52833. Even though everything seems to be working, there is no COM port listed on Windows. I've also tried Zephyr's USB CDC...
I got 2 NRF52840-DK Development Kit recently. But for one of the boards, the programmer firmeware encountered timeout during upgrade. The other board did not encounter this...
Hello All,
I am using nRF52840 Dev-kit and SDK 4.0 for Zigbee and thread. Due to some functions, we are using SDK 4.0 for this project which is not present in SDK 4.1. ...
Hello
In my another ticket https://devzone.nordicsemi.com/f/nordic-q-a/81555/ncs-upgradable-bootloader .
I know there is currently no support for upgrading the bootloader...
Hello,
I build my project with “Visual Studio Code” and with “SEGGER Embedded Studio”. There are some warnings when I use VS Code. When I use SEGGER to build the code...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1
I have below structure to frame the data packet and i need to send this packet to another thread through MailBox...
Hello.
I am developing with nRF52840DK.
Normally, I think that the buck regulator supplys 3.0V to Interface MCU and nRF52840.
I want to connect the 1.8V peripheral...
