Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hello
Based on this example : https://devzone.nordicsemi.com/f/nordic-q-a/57881/store-custom-application-data-using-peer-manager?ReplyFilter=Answers&ReplySortBy=Answers&ReplySortOrder...
Hi Support,
I am observing something that is quite strange on the GPIO input. I am developing a Zigbee device with Energy harvester with NRF52840. I need to use the state...
In addition to uarts, I2cs and SPIs I tried toggling some apparently spare pins without seeing voltage changes on the pins I tried.
Which pins are available for digital...
I'm using the Nordic nRF52840-DK board to breadboard an SDHC card interface in Zephyr using SPI. I have it doing "basic" operations, but am trying to reconcile what I'm physically...
Chip - BT832AF (nRF52810 QFAA)
SDK- nRF5_SDK_17.0.2_d674dde
SD - s112_nrf52_7.2.0
2V- power supply
My application need not to be very fast, but is extremely concerned...
Hi,
I am working on a project with 2 nrf52840 devices. One is the nrf52840 dk, while the other is a custom board with the nrf52840 module. I want to perform a dfu over uart...
I think this is a very weird requirement
Normally , I use manufacturer data to do this like picture below
it's easy and quick
but it contains len and type occupying...
Hey,
I am trying to get the Asset_tracker_v2 running on my Thingy:91, but with my own Cloud connection (It is a Thingsboard CE hosted on an ubuntu Server in Open Telekom...
I have to execute some lightweight error correction codes (ideally BCH) to compare and subsequently correct the mismatches between two binary arrays. I am working on the nrf52840...
I have been testing lte_lc_init_and_connect with my units inside a Faraday cage, This method doesn't terminate when it cannot get a signal (at least I haven't seen it). This...
I am attempting to install the nRF Connect SDK v1.5.0 on Mac OS X Big Sur, I have followed the Getting Started Assistant and Toolchain Manager with no success.
Here is my...
Hello everyone,
I am going to Integrate Bluetooth mesh into the nRF5 SDK example by using SDK 17.0.2 and SDK for Mesh V.5. I followed the instruction mentioned on the Infocenter...
I am from India. Recently I have purchased Thingy91. I have registered IBasis SIM as mentioned in the user guide. While registering the device in the nrf cloud I am facing...
