Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Hello!
DFU works correctly.
I try to enter chip in dfu mode from application by receiving command from SPI.
When command is received:
{ sd_softdevice_disable(); /...
Hi,
I'm using Zephyr with nrf52 and want to setup watchdog support with multiple channels (different timer settings for separate different threads).
I can add 1 channel...
Hi,
I have bought a Thingy 91 and have connected to the nRF cloud etc. and I am getting the sensor data OK.
The GPS is still not working, I have followed the instructions...
Hello,
I would like to calculate maximum range between two devices equipped with nRF52840 transceivers working in the IEEE 802.15.4 radio mode. Can I assume that -100 dBm...
Hello,
I have a question about Bluetooth connectivity issues. The BLE code I'm trying to make will be connected to the smartphone (Android). If phone out of the Bluetooth...
I'm developing a bluetooth device that only advertises data, it's set to BLE_GAP_ADV_FLAGS_LE_ONLY_GENERAL_DISC_MODE and BLE_GAP_ADV_TYPE_NONCONNECTABLE_SCANNABLE_UNDIRECTED...
Hello everyone,
Can I use the latest nrfutil 6.1.0 tool to generate the DFU zip file for the dual_bank_bootloader in SDK11?
If yes, do I need to keep the --hw-version...
Hi, I wanna enter the system on sleep to save the power up to 10uA(about tens of A). I am using nrf52840-dk with SPI LCD and some GPIOs in zephyr. Also I want to do DEVICE_POWER_MANAGEMENT...
Hi, I would like to run an nrf53 example project. I got the devkit, and after some struggle I am now able to compile and run a project.
I need to run an Bluetooth example...
This is really a question about best practice - I have some ideas of ways to do what I want, but wonder if there is some clean API-supported method that I haven't found.....
Hi, I am in design stage and i need to change nrf 8001 to nrf 52810. In this point i have a question about pin configuration in nrf52810, Can i use any pin for any use? i...
Hello everyone.
I know from Errata document that the GPS antenna soldered on DK is not working properly on the 0.8.2 version of the DK. I need to use GPS for time syncronization...
Hello,
We are allocating a large amount of pages (100 pages, ~400kB) for the Flash Data Storage module in order to hold collected data. As a result, the fds garbage collection...
Hi all, can the nRF52840 dongle be used as an external Bluetooth 5.0 peripheral via a Raspberry Pi 3 running Linux?
I received this message from my engineer
' The drivers...
This is based on the article fround in devzone here .
I'm compiling a simple Hello World and followed the instructions as per the nrf Connect SDK Turorial Part 2 .
To...
