Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hi, I want to store some personal data through flash in the LPN mesh routine. I read some posts and can be implemented by using flash manager, but I can't find the relevant...
Hello, I am working on storing words to flash using fds. I am working with the nRF52 DK and SDK V15.2.0. As mentioned in my earlier post , I am storing some critical state...
Hi,
Greetings!
I am using below setup:
SDK: v16.0.0
Mesh SDK: v4.0.0
Application: Light switch server and client
Hardware: nRF52DK
Distance between client and...
Hi, I am using ble_app_uart example for peripheral device and it will be powered by a 3.7 V battery. I need to use battery as long as possible. So I decided to make peripheral...
When I put the device into sleep it draws app 30 uA in sleep mode. Read in the manual: "Core standby current= 50 μA", "Current drawn if HFXO is forced on through for instance...
Hi,
I am trying to emulate a vendor's tool, whose BLE properties are configured as follows: Custom 128 bit Service UUID like XXXXXXXX- 0000 -XXXX-XXXX-XXXXXXXXXXXX
Custom...
hi, I am working nrf52832. I am making configuration file for nrf52.so I want to used Led3 set as high.
#define LED3 ((GPIO_PIN_CNF_SENSE_High << GPIO_PIN_CNF_SENSE_Pos...
Hi, I am looking to access nRF9160 modem via I2C. Essentially looking for hooks/ serial interface hand-off points used for instance in AT Client sample or Serial LTE Modem...
We have some devices out in the field with a mixture of application versions. In one particular case, we have device A on application version 10 and we have device B on application...
Hi there
I am having issues to perform disconnections from my central device when calling sd_ble_gap_disconnect()
most of the time I am able to disconnect properly using...
Hi Devzone:
I am researching how to maximize radio performance and stumbled on a statement on page 356 in the spec:
"Typical sensitivity applies when ADDR0 is used for...
Hi! Currently I have a nrf52840 devkit hooked up to an SD-card for storage through FATFS (using SPI). I would like to add a BME680 environment-sensor to the board and have...
1. I am trying to connect one node (say node A) from two android phones say phone A and phone B. The node A is configured as an on-off server for lamp 1, but it could not...
Hi
I am working on a project which needs to be developed on FreeRTOS, I am facing an issue i need logs at backend using RTT as my both serial_uarte are being used for communication...
