I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello, I am working on asset tracker from ncs 1.4.0 and on NRF9160DK when i try to concatenate doubles with snprintf it shows me nothing and returns a huge value (several...
I need to develop a product using the nRF910. I have downloaded files from the download page but when I expand the files to open they are LOCKED with a RED CROSS. How do I...
Hi DevZone,
Does anyone have any experience with performing a SD-Card format with the nRF52840 . This is to avoid removing the SD-Card from the hardware when a format...
Hi,
I tried programming the nRF5340PDK using the nRF connect programmer, but when I select the board I get the following log:
2020-11-11T13:04:58.307Z INFO Application...
Hello,
in our project we have a nRF52840DK as central and a BMD-300 (contains nRF52832 chip) as peripheral. The software on the nRF52840DK is based on the ble_app_uart_c...
I have a project where I am distributing code images to a number of devices with DFU (this is a custom bootloader)
The peripherals use a mixture of 52840 and 52811 SoC...
Hi,
I am currently using the nRF logging module to log data from a nRF52832-DK to my laptop via a serial connection. However, I would like to move over to BLE logging for...
I doing some basic antenna tests via RSSI and the logger output is quite important to me. So far, I managed to log my RSSI values and timestamp, as well as the ID of my devices...
hello Nordic
i am using nrf52832, sdk 16.0, s132 v7.01
i am scanning for ble beacon but i want to be able to change the filtered mac address (i still want to filter...
MCU: nRF 52832 SDK VERSION: 17.0.0_9d13099 SOFTDEVICE: 7.0.1 (s132)
I have an application with some custom services (4) with different characteristics number and behavior...
I was able to change the MAC address in the ble_app_buttonless_dfu example with "sd_ble_gap_addr_set( )".
But, when I enter the DFU mode, the MAC address changes to the...
Hello,
i am using nRF52832 Development kit.
and segger embedded studio for debugging
i have just started with NFC module. i run the NFC example "record_url" and it is...
Hi,
In the process of testing DFU on the hardware, I am trying to send the DFU Packets through a TTL Cable to a different pins(P0.02, P0.03. No HWFC) instead of sending...
Hi Sir
As subject, I have a nRF52-DK on hand, I'd like to use the "Bluetooth Low Energy APP" of the desktop nRF connect software to scan BLE device and connect it,
Just...
Dear community, good afternoon
We have been working with a coordinator, a router device and an end device all based on nRF52840 (Fanstel BT840F module) with nRF5_SDK_for_Thread_and_Zigbee_v4...
