We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi
i am new with nRF52832. i am trying to run fatfs example program. But it shows Disk initialization failed. what is the reason for it?.
i am using segger embedded studio...
Hi,
I'm using SDK 15.2 & trying to combine hid keyboard with custom gatt service, but it was not advertising. When I debug, it got stuck on the line below with error code...
Hi.
I'd like to use nRF52840 in our project. Can I use the SoC and Zigbee SDK for commercial?
UPDATE!
Have I any limits if I will use SOC and Zigbee SDK for commercial...
Hello,
I follow " Configuring and performing DFU over Mesh" instraction and face with error after trying to transfer new app: "No response after opening COM port".
I do...
Hi,
I am trying to merge dfu with Beacon application. I have added all the required file in dfu example, but I am getting linker error for bsp.o file.
I am using sdk 14...
m_cb.adc_state is set to NRF_SAADC_STATE_CALIBRATION inside the function nrfx_saadc_calibrate_offset(), but the value is never changed to NRF_SAADC_STATE_IDLE, even is the...
Hello
I'm trying connect central to 4 peripheralPeripheral has 3 different customization services. When I connected to 4 peripheral, I encountered the problem of service...
I have a question about "SEGGER Embedded Studio for ARM V4.12".
I want to place the section of the FLASH area arbitrarily. And, for example, I want to place the following...
There is now a TI CC2451 Bluetooth module as a reference. Using nRF connect to monitor the log content, it is found that when the mobile phone is connected to Bluetooth and...
Hi everyone, I have a question about GPIOTE.
What happens if for example, GPIOTE is used to configure a pin to detect a low to high transition, but the pin is already...
Hello
I have a problem with restarting advertising after disconnect event.
There are two scenarios:
In this case everything works fine:
I start advertising
...
Hello,
I started with the template app and tried to do two things on a nRF52832 using Segger Studio:
1) advertise custom service
2) use Application Timer and App Scheduler...
Cannot connect to nRF52840DK board using nRF Connect Bluetooth Low Energy app on Linux (Ubuntu 18.04 LTS). When I choose "Select Device" and choose my board, I get:
"Validating...
We have custom developed board using nrf52832. When I run the example program developed in SDK15.0.0 with Soft device S132 V6.1.1, no issue noticed in running debug mode ...
For creating a Bluetooth mesh Hub that will communicate to the Azure IoT server, which should be the best suitable ethernet board for connecting with the nRF 52 DK?
