Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
I am building a project with CMake, inside nRF SDK for Mesh 3.2.0, which uses the math library:
1. source file includes math.h
2. CMakeLists.txt adds m to target_link_libraries...
There are a lot of missing materials under the topic:
Software Development Kit > Previous versions of nRF5 SDK for Thread and Zigbee > nRF5 SDK for Thread and Zigbee v3...
I'm converting an already working LPN that went into SystemOFF with GPIO wakeup for lowest power consumption.
Now I want to use the RTC2 as a secondary wakeup.
I know...
I am currently developing on the nrf52840DK (Rev 1.1.1) using the mbed os.
To debug on the board using OpenOCD it is necessary to flash the JLink firmware for the board...
Dear Nordic community,
we as a company, have developed products with the nRF52832... currently, we're developing a product with the nRF52840 (because we needed USB).
My...
Hello
I would like to change the Tx_Power using softdevice.
The sd_ble_gap_tx_power_set command shows me the supported tx_power values as -40dBm, -20dBm, -16dBm, -12dBm...
I have make some custom board with the same layout as a BMD-300 evaluation board (pca10040) with the same MCU which is used on this evaluation board from RIGADO. This is BMD...
Hiya,
We're running a few experiments with a wireless-mesh protocol based on rapid flooding on a few nrf52833 dev kits.
We'd ideally like to use a channel contention mechanism...
Hi, I am working on nRF9160DK lte_ble_gateway sample, in that I want to scan for beacons UUID and major, minor value. nRF52 device is programmed with bluetooth HCI (UART)...
I have a custom board uses nRF52810. When I flash my board with examples include SoftDevice (sdk 16.0.0) nRF52810 restarts. I am debugging with oscillascop and seeing that...
Hello,
what is the realistic maximum speed achievable over RTT on the 52840dk (using SEGGER_RTT_printf) to RTT Logger?
I have tried modifying frequency and NRF_LOG_BACKEND_RTT_TEMP_BUFFER_SIZE...
Our nRF52832 setup is:
SDK15.0.0
S132 V6.0.0
We have a setup where we are using BLE for various purposes, in both the central and peripheral roles. We upgrade our...
hey i want to make my device act as peripheral to smartphone at the same time act as boradcaster an to reach that we need gap_adv_type BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED...
I just received the nrf9160 DK and gone through nRF connect ( V3.3.0) installing toolchain, cloning the nRF Connect SDK and downloading Nordics version of SES
The problem...
Hi all,
We want to create some smart home networks based on BLE Mesh.
1. Is it possible to buy Nordic Thingy, load our software (temperature sensor based on BLE Mesh)...
