We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hi Nordic Team,
In my BLE project when I was trying to add Device information Service(GATT) in BLE central multilink example code, once the connection between central and...
Hi,
I am trying to modify the code in the BLE_App_Buttonless_DFU_pca10040_s132 example is SES. Without any modification the code compiles fine and can be recognized by nRF...
My issue like this ticket
https://devzone.nordicsemi.com/f/nordic-q-a/39428/usb-msc-corruption
I suspect it is caused by a problem in the implementation of the NRF_BLOCK_DEV_QSPI_FLAG_CACHE_WRITEBACK...
Hi,
We encountered a problem when added new models through an OTA DFU. Specifically we upgraded a device with SoftDevice 6.1.0, SDK 15.2 and Mesh SDK 3.1.0 to SoftDevice...
Is it enough just to connect from custom board to P20 header(nrf52840-dk) SWDIO, SWCLK, RESET, from custom board GND to P20( GND_DETECT) and power supply to custom board from...
I need to enable UART1 in runtime in order to be able to read some data coming on that device.
In order to be able to use the uart functionality, I need to set CONFIG_SERIAL...
Hi,
As the subject description, I just remove the part of hid function from main.c then make the personal source file.
Before I removed, the project could work as usual...
Dear Nordic
there are two question find in my software. it may be some matter with thest two question, so put here together.
1.
My software will be reset about several...
for the i2c_3 to work the following is needed to modify the SDK.
nrf/subsys/spm/Kconfig
```
config SPM_NRF_TWIM3_NS
bool "TWIM3 is Non-Secure"
default y
```
...
I was wondering the behavior of the NFC BLE Pairing with OOB when max connections are full. Will the connections disconnect in order to pair with a new central after an NFC...
Hello,
in nRF52832 devices, P0.21 pin can be configured as reset using PSELRESET[0], PSELRESET[1] ergisters.
Due to space constraints, i dont intend to use the reset...
Hi：
I want to ask：the nRF24L01 can work in single point mode by SPI commands。 I need the wave show like in the picture。
IF it can,which software and hadware I need....
Hi,
I trying to send indication supplied with some data to my Android app (which BTW works fine with other BLE devices) as an answer to characteristic write command
...
I am trying to run a project on a Fastnel
BT840 module
I had the code running on The dev kit when we switched to the new hardware without a FL crystal I have been unable...
