Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi All,
I'm using Ellysis sniffer for debugging my ble mesh network.
I've made network setup using generic on/off application and I'm able to communicate and capture...
I have a nRF9160 DK and since I am in Germany, we are trying to use the most common LTE band they use here, which are:
Band 1,3,7,20
However, band 7 does not seem available...
When I compile one of the nfr_log modules (e.x. nrf_log_frontend.c) I get the following error.
I do include ../components/softdevice/s132/headers/nfr52 in my User Include...
I have an nRF9160 DK which came with an enclosed eSIM from iBasis, that is supposed to work in most of Europe.
However, after jumping through all the getting started hoops...
Hi All,
Posting this here after a lot of searching and troubleshooting. There have been a lot of similar posts but none actually seems to go into how to implement this in...
I'm successfully printing to the UART1 com port at baud rate 115200, but I have a peripheral I plan to connect that requires 9600. What is the proper way to go about this...
I'm using an NRF52840, SoftDevice s140, FreeRTOS, SDK 15.3.0.
I'm trying to sample my ADC at high speed, >1khz (10-40kHz).
I implemented the logic from the SAADC exaple...
Development environment：
NRF52832
SDK：15.3
SOFTDEVICE：NONE
When testing the FDS module power-off data protection feature, the FDS module is abnormal.
During the...
I have a PCB containing an nRF9160 using a SEGGER J-Link. I am able to update the application firmware at will using a variety of tools but if I use nRF Connect v3.2.0 to...
To the kind attention of Nordic support team,
I'm considering to get started manufacturing mini dongle nRF52840 based as in https://devzone.nordicsemi.com/f/nordic-q-a/48568...
I have the following problem:
I want to update my application code via BLE with the secure bootloader. This works perfectly while the J-Link-RTT-viewer is connected.
When...
Hello
I am using the basic asset tracker example + https://nrfcloud.com
I can see messages from the device to cloud, how can I send commands from cloud to device?
...
Like the question, I want the dongle to be detected as a bluetooth device but not a serial port. Is there any method to do this?
And I want to ask if it be possible to build...
Hi.
I'd tried to use proxy with ble_app_uart_coexist example.
(SDK : nRF5_SDK_15.3.0_59ac345 and nrf5_SDK_for_Mesh_v3.2.0_src)
I set MESH_FEATURE_PB_ADV_ENABLED =...
Hi ,
As per our requirement i need processor witch is capable of android application development from nordic semiconductor family. Please recommend me suitable processor...
